Jump to content
SAU Community

Recommended Posts

I'm moving to Canada so I am offering my 1995 r33 n1 for sale. It was the 6th 33n1 produced of 46 for 1995. I have fasted and recorded every vin from Bcnr 000000-Bcnr 009300. I have most of the information on an excel spreadsheet so you can sort every 1995 GTR into, colour or model type. Spread sheet to be complete and sold with car.

Mods include: apexi cold air intake,z32 afm's,has cam gears,sard 700cc injectors,nismo timing belt,stainless manifold dump pipe & 4" cat black with Magic 4" hi flow cat, Orc twin plate clutch and lightened flywheel,Tein HA adjustable suspension, slotted rotors & braided brake lines,power FC with hand controller, apexi ACVR blue screen, Xeon head lights, nismo 320km cluster & console cluster, Asuka racing wheels (Volk knock offs)

I personally have had this car upto 314kph without hitting the limiter and it was so stable I would be comfortable doing that round corners.

The car will be for sale until February 28th as I will need to make arrangements to take it to Canada in late March if it doesn't sell.

$50,000 firm.

post-111241-0-96363100-1422753121_thumb.jpg

post-111241-0-00528400-1422753165_thumb.jpg

post-111241-0-56474400-1422753195_thumb.jpg

post-111241-0-43512500-1422753226_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/453378-r33-n1-for-sale/
Share on other sites

  • 2 weeks later...

Thanks MP, I don't mind keeping it. The couple I've seen for sale in Japan over the last few years were 35 & 36k usd. With GST, shipping & compliance your very close to 50k, hope it doesn't get hurt on the way over and probably spnd upwards of 10k getting a few little upgrades. So that is what it would cost me to get the same quality N1. Also it is the 6th r33 N1 to be built which has been my lucky number since I was 6 years old.

Link to comment
https://www.sau.com.au/forums/topic/453378-r33-n1-for-sale/#findComment-7484584
Share on other sites

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...