Jump to content
SAU Community

Recommended Posts

(sorry if this isn't the right spot to post this)

So I took my R34 into the shop and of course, the lovely coilpacks had pooped themselves. Now i'm not an extreme genius on cars, just really know the basics and what not. Apparently it's going to cost anywhere between $1200-$1500 to replace the coils (Which i think is fair enough due to them being pretty expensive by themselves), as they're replacing all 6 of them. The bloke called me up and told me he couldn't pinpoint which coil it was, due to the "layout of the engine" or something along those lines.

My biggest question is, am I being taken advantage of due to my age, and what sorts of prices have you been quoted to change out 6 coils + labour?

Sorry if this is an extremely basic question, however I just want to double check with you all!

(R34 25gt, by the way)

Link to comment
https://www.sau.com.au/forums/topic/453707-quote-for-replacement-coils-labour/
Share on other sites

you are being taken advantage of. A good set of coils is like $500 and it takes literally two seconds to install them.

Well.

HOW FKN MUCH????!!!!

Take it somewhere else

SHIET.

Considering the establishment that diagnosed this problem, it would be worth reading up on how to change spark plugs and clean existing coil packs too.

You may find the coil packs aren't the problem, might be crook plugs, excessive plug gap, too much degreaser and so on.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
    • Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
×
×
  • Create New...