Jump to content
SAU Community

For Those Who Have Done The "twin Turbo" Pipe Mod

djvoodoo

By djvoodoo,
in Engines & Forced Induction

 Share

Recommended Posts

djvoodoo Experienced

djvoodoo

Posted
Posted

I have read the many forums about the pro's of doing this mod, so I bought myself a spare pipe from Ebay and had the divider put in.

Does it feel any different? Not sure. The weather is cold so it's very responsive anyway at the moment.... Might be placebo effect but it feels more punchy from 2-3.5K. On boost feels the same.

My question is:

Did you notice the turbo spool noise inside the cabin become more pronounced? I noticed that the turbo's "sound" quite different inside the cabin. Slightly more whiney/whizzy i suppose.

Piggaz Grand Master

Piggaz

Posted
Posted

Since your car makes a million horsepower If it's good enough for you it's good enough for me

It's a very lazy design from Nissan, regardless. It makes a huge difference. I have done a back to back test with Marko_R1's car. 3.0 and -10's. Without it, it chided like a steam train. With it, 90% of the shuffle went away. GT-RS's suck dick either way, but that is a first hand experience.

There are NO downsides to doing this mod.

MrStabby Grand Master

MrStabby

Posted
Posted

Would be good to see a before and after dyno run if anyone has done it.

+1, or even a flow check/pressure drop measurement of each.

Downside could be lower bang for buck than some other mod, when using smaller non-shuffling turbos. Piggaz - would you do this on a car with stock turbos? -7s?

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Was planning to do a before and after on Daz's car, as he plans to run one if it helps with flow. Should help even on a stock car as the front turbo entry is pretty bad.

Cheap and inconspicuous, I like those kind of mods.

Piggaz Grand Master

Piggaz

Posted
Posted

+1, or even a flow check/pressure drop measurement of each.

Downside could be lower bang for buck than some other mod, when using smaller non-shuffling turbos. Piggaz - would you do this on a car with stock turbos? -7s?

Micko's old man just threw this pipe on his -9/stock engine GTR. From the seat of the pants it feels a little more linear.

If you look at the pipe, the front turbo air is basically "merging" at a right angle to the incoming air from the rear huffer.

I believe Sean Morris did a back to back years ago. He was claiming 8-10 hp increase from memory. Have a search online. You should be able to find it. I can't remember the turbo setup he tested it on though.

Just do it, put it on and forget about it.

  • Like 1
mr skidz Veteran

mr skidz

Posted
Posted

here's a picture of my first gtr back in 2004, it had a polished cusco hot pipe and from memory it was very well made and I'm pretty sure when I looked inside it the merge was better than 90 degrees more like 45 degrees and it looked just a smidge bigger in diameter also.

post-60000-14331296415259_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      M35 Aftermarket Fuel Pump

      By MBS206 · Posted

      Pressure when IDLING, is meant to be 51PSi... So that amperage value needs to go up a fair chunk... I'd personally be factoring for more like 12amp at least on those runs, and at that point you need to hope the already there wiring doesn't drop you a volt or two, as that's a lot of fuel pressure flow drop off from 13.5 to 12V! Taking idle pressure of 51psi, means the pump will be drawing a MINIMUM of 9amps all the time based on your reading of the graph (3bar base, then allowing an extra 0.5bar for boost = roughly 51psi)
    • Ben_D
      Wanted to buy R200 longnose LSD 3.9 ratio

      By Ben_D · Posted

      Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Ben_D
      Back for more after 18 years - and where are the longnose R200 LSDs?

      By Ben_D · Posted

      Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • sonicii
      G35 Control arm and Compression Rods into a V35 Skyline.

      By sonicii · Posted

      Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
×
×
  • Create New...