Jump to content
SAU Community

Recommended Posts

  • Replies 89
  • Created
  • Last Reply

Top Posters In This Topic

powder coating wheels is a few hundreed bucks or so.

probably was steam, plus old oil and filters might be not helping.

it would be a good idea to have it on a hoist and check it out .. always good to check out the driveline if possible. though engine and bodywork and wheels all seems ok so maybe it has been well looked after in general anyway :cheers:

Re the alarm - I highly recommend Chris Rogers from Soundoff. He's mobile, but he northside too actually so it'd suit you to a tee. The man knows his shit. Mention SAU and tell him I referred you :D Ph 0407 102 839

For powder coating, PM Gary1 from these forums. He used to do that kind of thing for a living before a career change, no doubt he'd be able to recommend some good places.

On a side note - service the car immediately, and replace timing belt and idler/tensioner bearings or at the very least pull the timing cover off and inspect them. Also take it for a drive, head up a steepish hill at 80 or 100km/h, and nail it in 4th. As the car starts making power, listen for clutch slip. Also listen for pinging (back the fark off the throttle if you hear it!) and have a friend follow you looking for smoke of any description. A little fuel smoke when you first hit the throttle is generally ok, particularly if the boost is higher than stock, but if it continues or isn't black, back off and have it investigated.

You probably already know all this but I've said it anyway ;) They're all things I'd do regardless of what the previous owner says, for my own peace of mind.

Yea. It would be sitting the garage for a while so I would drop the oil, recharge the filters and do the timing belt then.

What does clutch slip sound like I thought that you would feel it rather than hear it? Pinging also I have no idea what that sounds like. I've heard lots of people talk about these things but if u haven't actually experienced them yourself it might be hard to identify?

The smoke bit makes sense. Thanks for the contacts will keep them in mind when the time comes.

']powder coating wheels is a few hundreed bucks or so.  

probably was steam, plus old oil and filters might be not helping.

it would be a good idea to have it on a hoist and check it out .. always good to check out the driveline if possible. though engine and bodywork and wheels all seems ok so maybe it has been well looked after in general anyway ;)

Yes *apparently* it was owned by some Chinese businessman so I think it may have been treated well. However, signs are that he got bored with his toy and let maintenance slip in recent times. I'll rectify that.

A slipping clutch is generally easier to hear than to feel as such - the revs will pick up faster than the speed does, so you could say that it's what you're "not" feeling that's the problem :D If you're not sure what to look for, it kind of feels like you're getting wheelspin.

Not far from my place there is a nice steep uphill section that's right next to a cement barrier - makes it very easy to listen out for this (and to spooling, exhaust, etc ;)) Basically if you get up it, and you think the clutch is slipping, back off the throttle and see if the revs drop more than a hundred rpm or so. Higher gears are better as there is more force acting against the engine, therefore the clutch is more likely to slip.

As for pinging, it sounds like a 'ting-ting-ting' noise. If you were to hit the block with a screwdriver, the sound would be similar to that. It might be fairly hard to hear or it might be really loud (danger will robinson!), and it might only happen once or twice a second, or many times a second. Any pinging is bad. Basically it means that the engine is detonating, usually due to timing being too far advanced, which pushes combustion pressures waaay above where they should be, increases heat, melts pistons, flogs out bearings and gudgeons and generally is a Bad Thing ™.

its standard fare. if buyer puts the deposit and then backs out. the selller has the right to keep it.  Seller had to turn away potential customers or remove the ad.

By law this isn't right, goto any layer and you'll soon find out what your've just said is illegal.

The person who has given a dipsoit hasn't bouaght your car nor paid for your time nor for an ad in any newspaper so the seller can't keep any depsoit given to them for any reason other wise the seller would be stealing the possablie buyers money from them.

As I said if the seller tries to keep the money they can be taken to court and have to pay back the money and maybe pay for the court costs as well, and maybe pay for time wasted as an extra cost.

And that's the law not some made up crap.

A despoit is only for telling a seller that you are interested in maybe buying the car and to keep them in mind before they sell it to someone else, you could still sell the car to someone else, it doesn't hold a car to that person as they havn't boaught anything from the seller, but they will have to give the money back.

You'll have to forgive my lack of photographic skills and shaking hands.

She's pulling to the right abit perhaps wheel alignment needed not under

brakes and not too badly.

The brakes are dam squeky, bit comical at the lights.

I didn't get up it too much esp since the dealer had put

standard unleaded in it (she'll get a good dose of optimax soon.

Being a GTST driver most noticeable things were later but harder boost,

longer legs, better grip, cornering is much different I actually clipped the

left wheel taking the first 90 degree corner. Wont be doing that again.

Probably cos i was nervous driver.

The panel damage is minor on drivers side should be easily fixed.

Effortless acceleration. Tendency for speedo to get up there very quick on even

low boost.

Time for TLC, clean, nice oil, filter recharge, and eventually panel beating.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys, long time no post as per usual! It's been a busy year so far, the biggest thing being a new job.  After 28 years in the automotive industry I decided it was time for a change.  I was losing faith in the industry and where it's heading.  Now in a completely different industry (electrical) working for a company that manufacture water pump contollers.  Not as sexy as cars but it's an interesting,  challenging industry. I now don't work Saturdays which is a bonus!  It's still 50-55 hours a week but having Saturdays ack after 28 years of working them is awesome!   No news on the GT-R but i did decide to add some more JDM goodness into my life....           1990 300 ZX.  She's not perfect but for a 35 year old car she ain't bad!  Just going to tidy it up a bit and enjoy it.  It's currently auto but will start stockpiling everything for a manual swap. It WILL distract me even further from the GT-R but im hoping not for too long! It somewhat proves a 6'8" freak can fit in a 300 ZX.  Sort of...  I drove it home from the previous owners house in Melbourne via Black Spur and Merton Gap (2 awesome bits of Victorian twisty road) and it was amazing!  Handles so well!!!   I don't think it would be worthy of a full build page but I'll post up some of the upgrades here if anyone is interested?  Cheers guys!
    • End game is to: - Remove all the slop from old worn parts - Adjust setup so that the wheels actually fit and the car is drivable (currently it is not because of the extreme rubbing on the guards).   Progress over the last couple of days, removed the rear hubs! Next steps: - Buy bushings - Replace bushings/bearings on hub - Reinstall
    • Cracked deck  And other cam snap stuff   
    • A few random issues have popped up since my last update. My WMI pressure sensor failed within about 10 minutes of it seeing liquid. It was a 20$ China special, so I'm not surprised. My name brand replacement should arrive today.  My power steering assist also decided to crap out last weekend. The usual, works for about 60 seconds after starting the car then I lose it. I dusted off my old copy of NDS and connected to the HICAS ECU. Code 4 for assist solenoid.... I tested the solenoid and it's fine.  I knew the day where my HICAS ecu would crap out would come, and I welcome it. It was the last HICAS part on the car that is now in the bin. I've ordered an SSR and I will control the power steering solenoid with my Haltech ecu. It will be nice to have proper speed referenced assist again after all these years.   
×
×
  • Create New...