Jump to content
SAU Community

Recommended Posts

Hey Guys,

I am more or a reader than a poster but i have come seeking advice.

I have what i believe to be, is a substantial vacuum leak in my 1994 S1 R33 Gts-t RB25det 4 spd Auto,

I say believe because at the moment, i am struggling to locate the problem,
Being of a non-mechanical background, i can only say that believe i have a substantial vacuum leak, because all the indications point to that at this stage such as:

- low rpm stalling, (4spd auto)
- stall at idle,
- stall when braking at slow speeds etc when the engine is at operating temperature.
- I have to switch the engine compeletely off, count to five and it will fire again no issues
- a softer brake pedal

My initial research lead me to the IAA/IAC valve at the back of the stock intake manifold so i had it looked at, and a new gasket fitted, but the problem remains, now even more significantly since they worked on it. The little coupe has become undriveable.

Can anyone shed some light on this?

Has anyone had similar experiances?

I have had my coupe for 15 years and never had an issue, this is the first time it ever given me grief.

If it is Vacuum, then i guess it is replace every associated gasket and hose on the left side of the engine until it is located?

Modifications to consider:

Cold air induction

FMIC.

Other that than that the Engine is utterly stock.

Attached are the most recent photos of my twin cam, merely for reference, however note that the blow-by hoses 2 and 3 and now NisGen parts.

Cheers Guys,

Regards

Jeff

post-140068-0-28034600-1436356588_thumb.jpg

post-140068-0-21166000-1436356603_thumb.jpg

post-140068-0-23380400-1436356615_thumb.jpg

Did you clean out the IAC when the gasket was replaced?

The AFM Solder issue is also quite common

Do you have BOV that vents to Atmo?

"stall when braking at slow speeds etc when the engine is at operating temperature."

I have this issue on my 1994 R33 S1.5 Manual and from what I've been told this is a common issue due the BOV

Did you clean out the IAC when the gasket was replaced?

The AFM Solder issue is also quite common

Do you have BOV that vents to Atmo?

"stall when braking at slow speeds etc when the engine is at operating temperature."

I have this issue on my 1994 R33 S1.5 Manual and from what I've been told this is a common issue due the BOV

Hi Ben,

The instructions given to the workshop were to remove, clean and replace the IAC with the new gasket.

The new gasket is clearly visible and i was assured that the valved was cleaned....without removing it, i am guessing there is no way to check the work.

I hadn't thought of the AFM sensor, i will chase that up, much appreciated, thank you.

The blow off valve is factory standard, did you mean after fitting an aftermarket one? or with aged stock ones?

Thanks for the reply mate,

Cheers,

Is the idle higher?

It's very easy to check AAC. As in super easy. I don't see how they could clean it without removing it. Unless they put upper engine cleaner through the car.

G'Day Mate,

The idle all good, it was a little high when i got it back from the workshop, but has settled down now. Should i look for something in relation to that?

I had been tempted a couple of times to remove it and check, i have a spare gasket, and given that the gasket is new, it maybe safe to remove and inspect.

But like i said, i am non-mechanical. By your comment of "very easy to check AAC. As in super easy" inspires me to maybe give it a go.

Thanks mate,

Is your BOV return going anywhere? Im looking on my phone so the pictures dont come up great, but looks like it is either blanked or not going to the hardpipe

Im happy to be wrong. Just looks a bit like that

There appears to be a kink in the hose from the exhaust rocker cover vent down to the turbo. Maybe take care of that before you try anything else.

In the first post he says that's sorted.
  • 2 months later...

Hey you lot.

So a month or two down the track,

turns out there were two issues, not one.

The IAC/AAC was the issue with the low speed stalling.

Turns out the mechanic did FA when it came to the resto on it.

I took it off my self as suggested above and sure as sh1te nothing had been done at all, he had simply replaced the gasket.

An hour or so later and a bucket load of carbie cleaner sorted out the low rpm stalling.

But, it did not address the other issues, so now it will hesitate, jerk hard, stutter then it will simply lose all electrical power for a few seconds, then stall.
This can happen at speeds between 40-110km/hr, and it is getting very dangerous.
No warning lights appear on the dash at all (i.e the engine warning light) until it stalls, then all the dash lights come on as it would if i turned the key one past acc.
After pulling off to the side, i need to then switch the engine all the way off, count to five, then it will fire instantly.
One of two things will then happen, either it will fire up and continue without issue, or, immediately repeat itself 5, 6, 7 times until it "clears" and I can get home.
Further to note, it can be either at cruising or under acceleration, but not as i slow.

So I am still chasing bugs.

What i have done so far:

cleaned the throttle body,

cleaned the AFM sensor

CRC'd every electrical connector i could find,

checked every coil pack,

checked every spark plug

cleaned my K&N pod with recommended cleaner,

But still it persists,

Any guidance would be well received!

Any suggestions or similar experiences?

Cheers guys,

Check your ECCS loom is connecting to the main loom properly. Been in a car that had a similar problem and it was because the ECCS loom was not connected to the main loom properly, it came loose somehow. It's the plug which is grey in colour and sits near your coolant bleed plug and fuel rail, quite easy to spot.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
    • The old approach was to fill the cylinder/chamber with a length of rope pushed in through the sparkplug hole. The new approach is to connect compressed air to the sparkplug hole and fill it with enough pressure to push the valves up. Doing either of these things with the head on and the engine in the car is a lot less pleasant than doing it properly.
    • Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
×
×
  • Create New...