Jump to content
SAU Community

Recommended Posts

  • 1 month later...

ok went on a job in Texas for a bit. So the car sat for a few weeks. But I got some work done.

Did the brakes.

reIfoWH.jpg

jsyfmfr.jpg

Looks a lot more clean. I think the car had original rotors and pads. The front could have been changed they had life on them....the rears were getting really close to metal lol.

Mvmc6sZ.jpg

Also got the oil cooler/relocation kit done.

zhBTrBQ.jpg

htHDRoU.jpg

WCgBP1w.jpg

l7Cb1PZ.jpg

44dZ1hc.jpg

98i0IiR.jpg

6D0b1Yw.jpg

I wish I would have tried to do an oil change first before buying this lol. It is no where near as hard to get to the stock filter as the internet makes it sound. If you have big forearms, I can see why. But if you are relatively small, try it first. It literally took 5 minutes to get off. That was because it was on pretty tight lol. Probably would have just got a sandwich plate and cooler if I knew that. But it works very well, temps definitely stay down.

Also got some more parts in. Forgot about these lol.

N1 brake air guides, these work really well with the factory undertray/ lip air guides.

gRInn8s.jpg

0sFE9XH.jpg

Also got some new turbos. Figured I'd give these a shot. GCG hi flowed -7's.

qJKVAkt.jpg

Edited by JTCC

they just go on the tension rod. I haven't put them on yet. Its just been rainy and cold here. I don't take the car out in bad weather. If you still have the factory duct work from the lip they work perfect. On standard GTR they just dump into the wheel well brake area with no further direction. These guides pick up perfectly where the ducts leave off and direct that air onto the rotor.

cool ill see if i can get them new. wouldnt mind a set

Yea I'm not sure if they are still available from Nissan. I don't think they are, but they could be. This guy just had them and never used them.

  • 2 weeks later...

had the old tensioner squeel going on. Cold weather must of really got to it. It got pretty bad, started doing it at idle also. At first I thought it could be the fan, but it never went away no matter how warm I got the engine. Sounded like it was from the front cover, so I just assumed it was the tensioner. Glad I had all the stuff sitting around. Replaced water pump, idler, tensioner, spring, cam gears and timing belt. Wish I would of had a radiator and harmonic balancer lol. Perfect time to change.

out with the old, in with the new.

poGpjw6.jpg

TvaXaAb.jpg

nmiWL1h.jpg

feamg7U.jpg

XCGFr1l.jpg

Edited by JTCC
  • Like 1
  • 4 months later...

Ok got a few parts in.

WvLs24X.jpg

Omori Factory BNR32 aluminum inlet pipes

r9hmo22.jpg

Sard racing aluminum radiator

og3dq51.jpg

G82byY0.jpg

4gDDmnX.jpg

Nismo super coppermix twin disc

ZBLAcp9.jpg

HgpqhJl.jpg

nT7iQDL.jpg

Midori hicas cancel

y6grbNR.jpg

PXnZOTy.jpg

Nismo transmission and motor mount set

skgu4iS.jpg

Nismo clutch-pivot

dAPwUnw.jpg

OEM dust boots

d2JiZst.jpg

Nismo oil air separator

Y2ziOkC.jpg

Nismo intake plenum

doRCQeV.jpg

Part 2 (picture limit)

Nismo clutch line

07CCqZg.jpg

Nismo aluminum Inter cooler pipe set

Eiifc4s.jpg

Nismo oil pump

R7GbfdX.jpg

Nismo oil pan baffle

OfDMD2J.jpg

TPymtU6.jpg

Greddy profec OLED boost controller

AIv3VHm.jpg

Fluids package

5rreTZw.jpg

OEM r32 GTR brochure and optional parts catalogue's

GMIN9Da.jpg

k1Luv8x.jpg

7Kj4DBA.jpg

9BQA8n2.jpg

cm9gNBi.jpg

Nismo 1996 vol. 7 parts book and Nismo 10th anniversary r33 parts book

NTbe9lz.jpg

KaFeQRf.jpg

LREcHjX.jpg

mGVYNgM.jpg

Edited by JTCC
  • 3 weeks later...
  • 2 weeks later...

Few more little things.

Nismo steering rack bushings

IizUYwd.jpg

OEM rain guards. Not sure if I'll use these, Just bought them for future use. I can't decide lol.

KQbFyt6.jpg

All new OEM emblems

uGt9rzH.jpg

Picked these old Recaro Crayola up. Probably put these in my s13 though. Some old school 1990's goodness.

rXDqk7v.jpg

L1J8icm.jpg

slf7Bbk.jpg

Gave the car a good wash. Took a cell phone pic. Thought it turned out pretty well for a cell phone. Nice and shiny.

zfGv8x2.jpg

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
×
×
  • Create New...