Jump to content
SAU Community

Recommended Posts

Selling my HKS v-cam step 1. Comes complete with cam, wiring, sensors. They normally don't come with cam gears or exhaust camshaft but this will :)

Perfect for gtss or 2530 turbos.

$4800

In adelaide

post-38653-14440890079351_thumb.jpgpost-38653-14440890656109_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/460180-hks-step-1-v-cam/
Share on other sites

The $2990 Otomoto kit is the bare bones though.

You still need the following:

-Exhaust cam upgrade to make it worthwhile (optional)

-RB25Neo intake cam phaser and solenoid, plus you need to mod the phaser.

-ECU or rpm controller to control the solenoid, wiring

-Mod your 26 front cover (ie cut hole) or remove to fit the longer cam gear phaser.

For an extra 1K or so can get the HKS goodness :P

Can you change a step 1 to step pro using the option parts from RHD Japan?

It might appeal to a wider buyer base if possble

I looked in this a lot last year. You can only go from step 1 to a 2. Couldn't see an option to go from 1 or 2 to a pro, unless it's changed?
  • 3 weeks later...

Do these things really make $4800 worth of difference to a car?

Legit curious

Sure does, v cam is better then the ottomoto kit.

V cam is completely variable where as the ottomoto is stepped

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...