Jump to content
SAU Community

Recommended Posts

Well guys the time has finally come for the event everyone has been looking forward to!


It is our Putty Road Cruise up to Singleton!

Date: Sunday 13th of December

Meet Location: Corner Windsor Road and Groves Avenue McDonald's / KFC

Meet Time: Meet at 9:00am for a 9:30am departure

Destination: The Royal Hotel, Singleton

Map: https://www.google.com.au/maps/dir/-33.6257063,150.8382563/-33.60192,150.8219818/7755+Putty+Rd,+Garland+Valley+NSW+2330/Royal+Hotel-Motel,+84+George+St,+Singleton+NSW+2330/@-33.0283837,151.3019527,10z/data=!4m16!4m15!1m0!1m0!1m5!1m1!1s0x6b0cfd0f940d6db7:0x818eda6b9975306!2m2!1d150.748518!2d-32.9074811!1m5!1m1!1s0x6b0cafd7fd5df341:0xb21f7907d7a5223e!2m2!1d151.1759855!2d-32.5629127!3e0?hl=en

We will meet at McDonald's / KFC on Windsor road and from there will head onto Putty Road.

From this we will stop at the Halfway Truck Stop which we should reach at approximately 11:30am.

For all the Newcastle folks this will be a good point to join up.

From here we will continue on to Singleton for lunch.

Please remember to fill up prior to heading onto Putty Road. There will not be a fuel stop until Singleton.

At Singleton there is a range of servo's available including BP, Shell and Caltex.

There will be a lead and follow car so no one should get lost.

We will also be bringing along walkie talkies to keep the group together so if you have one please bring it along.

If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior!

This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days.

This is an official SAU:NSW event and will be run under a CAMS permit.

One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general.

When attending one of Skylines Australia NSW events please try to:

• Be aware of surrounding environment and act accordingly.
• Drive courteously on the state’s roads as a true enthusiast should.
• Understand how important it is to maintain the good name of SAU:NSW and thus, treat others accordingly.

• Any misbehaviour will not be tolerated and you will be asked to leave.

Thanks guys and hope to see you there!

Attendees:

1. RBrennan25 +2

2.

3. Terry_GT-R34

4. crashdown

5. GTofuS-T

6. Grease

7. BenRThirtyFour

8. Mihalis

9. Dark26

10. pureplaya

11. sammi_d

12. Yo-Yo

13. Murray_Calavera +1

14. Aqua

15. CaptainFresh +1

16.

17. BunsenBurna

18. stagea pete

19. rosella +1

20. SiNNO

21. chriszila +1

22. Victory

23. Clinton

24. PR34CH

25. Fdawgg +1

26. roy8532

27. anthony_rs4s

28. Bodella

29. bluenoir +1

30. NISMO

31.

32.

33.

34.

35.

...

In the process of getting that day off so pop me in please Chris!

Do we have an idea what date the January meet will be?

At the moment we are still finalizing the date due to New Year Holidays, School Holidays and Public Holidays.

Rough date would be weekend of 23rd + 24th but yes need to confirm.

This was taken from the exact same cruise 2 years ago.

https://www.youtube.com/watch?v=ru2WUf1SuxA

Adam can I put your name down for this?




  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...