Jump to content
SAU Community

Help Wanted For Tuning

DPham

By DPham,
in General Automotive Discussion

 Share

Recommended Posts

DPham Explorer

DPham

Posted
Posted

Hi Guys i am quite new to the car scene i recently just purchased a 180 shell which i overpaid for quite a lot for since i didn't really know anything about cars. Previously i owned a honda integra dc5 type S which was both my daily and weekender toy. I have currently purchased over 10 grand in second hand parts which have not even been installed yet. The shell has a fair bit of rust when i purchased the shell as did not check under it as i was suggested to buy this shell by my best mate who owns a black s2k . I'm planning on paying for a 3 grand respray which includes dent repair and rust repair. There is a hole caused by the rust underneath the chassis but i was told that a plate is going to be welded to it so it should be fine. So far i have spent 12k on the car and it is still not running right to the way i want as it is in need of an oxy sensor and afm.

I am only a P plate driver so i want to keep the car P plate legal. I want the car to make at least 250kw at the rears and i am willing to pay for parts needed. I was told sr20de engines easily make 400kw. I was told of several places that can do this is Garage worx, Edge motorworks, Jak motorworks and Chasers Motorworks as these shops are considered nissan specialist and can dyno tune my car for 250kw.

i don't really trust jak and chasers so i won't take my car to them. I would like your thoughts on Garage worx and edge motorworks.

Link to comment
https://www.sau.com.au/forums/topic/461505-help-wanted-for-tuning/
Share on other sites
Leroy Peterson Grand Master

Leroy Peterson

Posted
Posted

If you run space savers on the rears it will feel like it makes 250kw.

But seriously its not worth the time or buckets of money to get that kind of power from NA. Buy turbo bits then wait till youre old enough. A $3k respray is going to be fairly shit, and thats not even including dint or rust repair.

Hertz Donut Proficient

Hertz Donut

Posted
Posted

SR20DETs can make 400kW. SR20DEs, you'll be spending a lot of money to make 200kW. A "T" makes a big difference.

Now, I'm from a small set of islands far off the East coast of Aussie, but from what I understand "over 10 grand in second hand parts" and "P plate legal" don't really go hand-in-hand, unless maybe that's all stereo gear or a very, very fancy set of wheels that will go missing in about 4 weeks' time. I thought engine mods were pretty much a no-no?

Birds Grand Master

Birds

Posted
Posted

OP, you're getting "told" a lot of things and spending money on hearsay. Stop listening to friends and start reading or asking professionals.

Agree with above; cut your losses any way you can. Accept you made a mistake and move on. Dreams take time and you're rushing in gung-ho. Buy a decent n/a car for your P plates and then sell it. Then buy a decent turbo car. Do nothing but this.

3k with dent removal will be a shit job unless part of the deal is you're doing the spraying yourself...in which case it will be a shit job.

DPham Explorer

DPham

Posted
  • Author
Posted

Thanks for the advice guys...

I have contacted Garage worx and they told me not to give up hope on the car. They told me i can still be restored and since I've already spent so much on it i shouldn't really cut my losses just yet. Garage worx told me to proceed with the 3k respray and repair as they told me it's a really good quote so i will be getting the car resprayed next week.

DPham Explorer

DPham

Posted
  • Author
Posted

Sweet.

Post pics please. Before and after the plate gets welded over the chassis rust.

Is the shell rego able?

i'll try to get some photos in

i think the shell is able to be regoed, when it was a det, it was once regoed so i'm pretty sure it can be regoed

Hertz Donut Proficient

Hertz Donut

Posted
Posted (edited)

Oh lawd. Stop. Stop stop stop stop stop.

Stop.

"I think" doesn't cut it when it comes to rego, unless you intend to keep it off the street, permanently. Find out FOR SURE if it's still able to be rego'd before doing ANYTHING else. There's no need to rush through this, you'll only get further in the hole.

I really hope this works out for you, but you need to step back and do some due diligence before carrying on.

Edited by Hertz Donut
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...