Jump to content
SAU Community

Recommended Posts

I have an upper cracked radiator for an NM 35 axis au tech 2002 model.

Just below fuel cap neck on the right hand side. Perhaps 7cm from neck

Replacement will cost $1100 with labor. is that a reasonable price .

What choices do I have with radiator.

Repair iis not an option I was told

I can't do this myself.

With no coolant touching the sensor the temperature gauge was reading near normal.

I thus thought the car was operating normally every time I glanced at the gauges.

I was thinking of buying an oil temperature

or oil pressure gauge so I can get better engine information .

Is that over kill.is there a preferred choice amongst you guys.

If I am going to get another gauge what other gauges might be an option.

Is the such an animal out there as an oil temperature pressure gauge.

Can't see any online. What's the best brand please?

What are your thoughts

What will my 2002 model allow me to do in terms of oil

gauge dashboard placement.

Hoping for a quick reply to sort out my options

Also where do you suggest this gauge goes ?

I don't want to rip out

my satnav DVD player nor the TV screen .

Would prefer to have near other gauges but assume because of cost

I will have to pay for it to be installed near the driverwindscreen Pillar.

If there's was no coolant how long could I drive for without doing some damage ,

assuming engine was cold.

Assuming car was warm

How do I know I already know I have not done damage .as far as I can tell

Engine is okay

Thanks in advance for any thoughts

This leak continued for at least two days of driving unnoticed

but I don't know where the level was during those two days or more

Do sensors have to be reset or air removed from system.

What happens if coolant is just added to a new radiator replacement.

How can I tell if the job has been done properly

apart from the fact that there would be no leaks

I would sugest that an alloy radiator would be the way to go I have replaced all the Stageas and the 32 with alloy. $300 each. Try Just Jap..

Who told you that it was unrepairable - a mechanical workshop or a radiator repair shop? Find another radiator repair shop for an opinion. I have had new tops put on my radiator for a lot less than the price of a new radiator and I have also bought new OEM radiators which have been fine and not unduly expensive (around $300). If yours is original it is 14 years old. Personally I would buy a new stock radiator from a radiator speialist.

A radiator shop will replace the anti freeze/conditioner and bleed the system.

Gauges are great but if they are going to cost you an arm and a leg just check your water and oil levels once a week.

Top tank not repairable as was told made of plastic.

I assume true...is it true... according to midas muffler.

Top tank is not repairable but can be replaced. Would you take your computer to a carpenter? Go to a radiator specialist.

  • Like 1

A new top tank for an NM35 is worth as much as a new radiator; buy the one that Lakes101 and move on with your life.

It's larger, and better suited to our conditions than the undersized stocker; your car will thank you.

I have fitted about 6 in the last few weeks, pretty common. Some brands require a fair bit of cutting so beware.

Alloy ones can have their own issues, probably due to the Chinese quality control. I prefer the plastic tank M35 specific ones these days.

I used the radiator Scotty was just mentioning. Fitted it last weekend.

It's at least twice the thickness as the standard and didn't require any modifications at all.

Took maybe an. Hour to do the swap, not a hard job on the m35 at all. But bleeding the cooling system is another problem all together.

Definitely look into the "coolant bypass mod" on these forums.

I also just did this on the weekend along with a new thermostat.

Took very little time to bleed and the car now sits lower on the temperature gauge.

Edited by Bmx537

Had no choice but to send to Midas, locally as Nissan Indooroopilly and Nissan Moorooka refused to accept my towed vehicle being a personal import !!!!!

I will remember that .

Definitely not happy with price gouging at midas but car not driveable thanks for the info so far

Had no choice but to send to Midas, locally as Nissan Indooroopilly and Nissan Moorooka refused to accept my towed vehicle being a personal import !!!!!

I will remember that .

Definitely not happy with price gouging at midas but car not driveable thanks for the info so far

What do you mean you had no choice? I see there are many radiator repair shops in Brisbane such as

http://www.reddevilradiators.com.au/index.php/radiators

V35 350gt G35 look to be similar but are 26mm rather than 16mm

Wider by an inch or two, meaning there is a substantial amount of cutting for the shroud and fiberglass front.

V35 350gt G35 look to be similar but are 26mm rather than 16mm

I found that to be the case with C34s.After fitting an FMIC and FFP, I somehow fitted a 26mm plastic rad instead of the 32mm. My fault it was early days with the Stags and never noticed it. I had overheating problems. The stock water temp gauge never went over halfway, but when coming up the mountain the oil temp gauge I fitted went up to 120/130.+.And it started to boil in the back of the plenum.

Once I fitted the 50mm alloy, no more boiling and oil temp always less than 100.

Had to do a bit of cutting but well worth it.

Edited by 66yostagea

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...