Jump to content
SAU Community

Changing Brake Pads Without Removing Calipers? How To Compress Pistons?

V28VX37
 Share

Recommended Posts

V28VX37 Veteran

V28VX37

Posted
Posted

Hi guys,

This is a really basic question but I can't find a clear answer: Is there a good way to change front brake pads without removing calipers?

I read somewhere to turn old pad sideways and lever against the disc using it. I've tried this but it's still really hard going, the pistons are really tight.

I have removed the brake fluid reservoir top too.

Any tips on how to do this easier? Do I need a special tool?

The car is an R34 GTT with the standard Sumitomo calipers.

Trex Grand Master

Trex

Posted
Posted

quick search and i found this, not sure how well it would work.

corvette-brakes-17.jpg

I've had my pads out about 4 times in the last 2 weeks (because of squealing issues) i can't see any other way except for taking the caliper off, or possibly using that tool if it works well.

Also very interested if there is an easier way.

  • Like 1
V28VX37 Veteran

V28VX37

Posted
  • Author
Posted

quick search and i found this, not sure how well it would work.

corvette-brakes-17.jpg

I've had my pads out about 4 times in the last 2 weeks (because of squealing issues) i can't see any other way except for taking the caliper off, or possibly using that tool if it works well.

Also very interested if there is an easier way.

Thanks mate! What's the best way to compress the pistons with the caliper off, without a tool like that?

That tool does actually make sense if it's big enough - pull pads out on both sides and push opposing pistons in using the tool.

The other typical issue is the other piston popping up when you compress the other on the same side, so ideally you'd have two of these tools...

admS15 Grand Master

admS15

Posted
Posted

Thanks mate! What's the best way to compress the pistons with the caliper off, without a tool like that?

That tool does actually make sense if it's big enough - pull pads out on both sides and push opposing pistons in using the tool.

The other typical issue is the other piston popping up when you compress the other on the same side, so ideally you'd have two of these tools...

G clamp. Leave 1 pad in and use clamp to compress 2 pistons, then put the pad on the 2 pistons in the other side of caliper and repeat. Done.
hardsteppa Grand Master

hardsteppa

Posted
Posted (edited)

Use the ring end of a spanner bigger than the ID of the piston, say 19mm? Lever it carefully against the rotor with the ring end resting inside the piston and will push it in without issue, i have found.

Edited by hardsteppa
V28VX37 Veteran

V28VX37

Posted
  • Author
Posted

Thanks guys, looks like a combination of old pads, flat steel, spanners etc did it. Would have been quicker to just take the calipers off :)

I have ordered the tool Trex posted above to see if it saves some hassle next time.

V28VX37 Veteran

V28VX37

Posted
  • Author
Posted

Thats is seriously a waste of money, a screwdriver or spanner is all ive ever used on all cars

Hehe yeah it's pretty basic ... however if it saves me an hour next time it'll be worth the $25 :)

75coupe Grand Master

75coupe

Posted
Posted

Youll get better at it the more you do it, its a 30min job changing the front pads now for me, no special tools required...

I find those types of tools just give chance to your caliper paint getting scratched and another tool to grab for the job...

  • Like 1
V28VX37 Veteran

V28VX37

Posted
  • Author
Posted

Youll get better at it the more you do it, its a 30min job changing the front pads now for me, no special tools required...

I find those types of tools just give chance to your caliper paint getting scratched and another tool to grab for the job...

I reckon that tool will take longer than a screw driver

Ok ppl with your fancy screwdrivers, do you just lever off the disc to push the pistons in? Or chuck something in between?

75coupe Grand Master

75coupe

Posted
Posted

Use a lever under the old pad to push the pistons back. Pull out one pad so you have some room, it will allow the rotor to have small amount of movement as well

dermy Collaborator

dermy

Posted
Posted

https://www.gettoolsdirect.com.au/kincrome-4-in-1-brake-pad-spreader-k8165.html?gdftrk=gdfV26854_a_7c442_a_7c1200_a_7c93871&gclid=CKX8qaP2ossCFQx9vQodP0AHJA

You could use this and not have to remove the caliper. But like everyones said i just lever with e screw driver

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Quieter performance exhausts (or muffler add-on options)

      By Murray_Calavera · Posted

      Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • f00stx
      Quieter performance exhausts (or muffler add-on options)

      By f00stx · Posted

      So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...