Jump to content
SAU Community

Recommended Posts

I have some 255/40/17 on the rear of my car fitted to some R33 GTR stock rims. I was at the tyre place today and they did not have any tyres of this size.

They did have some used 245/40/17 Toyos and 255/45/17s.

Has anyone broken with tradition and used 255/45/17 instead of 255/40/17s?

Other than the speedo vs actual speed you are travelling, what would be the issue?

Link to comment
https://www.sau.com.au/forums/topic/464314-2554517-instead-of-2554017/
Share on other sites

See what the diff in rolling diameter is, because;

From vsi-09-rev4.pdf (NSW);
"The outside diameter of the wheel and tyre combination must be no more than 15mm over the largest diameter wheel and tyre combination specified for the vehicle and not more than 15mm below the smallest diameter wheel and tyre combination specified for the vehicle"

If you dont know the maths, google an online calculator.

How wide is a 33 GT-R rim? 8"?

If that's the case, you probably only need a 235/45 tyre. (245/45 max)

I'm surprised the "tyre place" couldn't give you a definitive answer.

(similar sizing rules apply in Victoria, fyi)

The tyres that had were Sailun's. I've not heard of that brand them before.

My choices were Nexen Nferra Su1 (I have them in 235 on the front and no complaints thus far), Nangkang, Archilles and that was it. I know they are all on the budget scale, but I cannot afford Bridgestones or anything past $160 per tyre at present.

I guess I wouldn't mind my speedo being more accurate, but in a way it's nice to know I got a little safety buffer there haha.

I've heard of folks putting on 265 tyres on their stock GTR rims. Has anyone done this or would you then start scraping the guards?

Crap tyres brah. Sometimes tyre shops keeps good second hand ones (I got Advan sports for $100, they were in good condition).

I've been using a set of used Bridgestones on the rear that cost me $50 each. I believe there were a very expensive tyre as they are the no flat ones as well. But they are worn now so it's time to get new or "new" used ones.

255/40/17 isn't a popular size at the second hand places unfortunately unless I go with the 245/40/17 Toyos at $50 each.

hardsteppa, where is that from? Jax? I won't put 235s on the rear seeing as how they are already stretched a bit on the front.

Even cheap tyres are going to be better and safer than the Bridgestones I've got that are past due for replacement.

I was just having a look at the pricing of re003 in 18", quite reasonably priced for say a 245/40/18 at 250 each b4 offer but then you look at a 265/35/18 which is what I run and its a whopping 409 each. Wtf. I was liking the sound of the pricing on these until I saw that. Back to the drawing board for my next tyre. Lol.

OMG wow, so the tyres I've been running on the rears are Bridgestone Potenza RE050A 255/40/17 runflats. Did a quick search on Jax's website and they are $359 each. Best $100 I ever spent that's for sure lol.

So going from those to Nangkangs or Nexens is going to be stepdown for sure. I still don't quite understand the speed ratings and all that though. I don't race or drift my car, it's a daily driver with the odd rare burst at the lights.

Nangkang have these two models in the NS-20 range.

71yKgwHibhL._SX522_.jpg

255/40ZR17 94W

255/40R17 94V

Was quoted $159 fitted each.

Yeah re003s work out to that price on the buy3, get 1 free deal from anywhere that stocks bridgestone i believe on current promotion.i got them from Jax who in my 2 experiences so far are shit. First one threw in free wheel alignment which was appalling, much worse than went in, and this latest, wheel balancing is bad vibes at 100k, frkn dangerous at 140k. Am going to go to trusted tyre shop and pay to get rebalanced.

Found a near new set of Kumho Ecsta KU19 255/40R17 for $85 each. Going to get them fitted on the weekend.

I've been to Jax once to get a puncture repair. They proceeded to tell me I wasn't allowed the Bridgestone Potenza RE050A funflats on my car. Nah uh, nope, I wasn't allowed to use them they said. Thus they could not repair the tyre. WTF!? So I had them put the tyre back on, and drove to the local guys who fixed it for $20 with the old tar & rope repair method. It Hasn't leaked since.

You don't have to worry about speed ratings as you don't drive >110 km/h.

Keep an eye out on ebay/forums as sometimes you can find good tyres going cheap.

I will never recommend Nankang, I bought some cheap 17" wheels once (how said that forged Volks go for less than $1k) with had near new NS-2 fitted, was shit in the dry and downright dangerous in the wet. Only drove it for a few days because I was waiting to get good tyres on my 18" R34 wheels.

But I guess if you're desperate it'll do. See if you can get Kumho (KU31), they should be priced around that much.

Don't even get me started on shit alignment jobs...

^I seriously doubt they will be anywhere near as good as re050a. They have a hardness rating of 140 which is quite soft and come out as factory tyres on many performance cars such as ss commondores all the way through to some Ferrari's, believe it or not. They where my favourite street tyre until I started tracking. There is also many different versions of them and they have been around for quite a while now but are still in production. Anyways, they are an awesome tyre, especially when you get them cheap. You definitely scored when you bought that pair. I suppose if the kuhmos are no good, you can always just skid them out of existence :yes:

You're probably right about them not being as good as the RE050As, but I always knew I scored when I got them for $50 each. Back to reality now, so if they aren't as good, I still hope they will be good and worth the $85 I paid each for them. I used to have Nexen N6000s on the rears and when they got low in tread, they sounded like a truck. Loved the look and tread pattern, but they were so noisy and lacked grip, especially on say grass or anything other than a hard flat surface.

My Lib came with KU19, noisy and not that not much grip, but I'm a bit spoilt as my GT-R had FK452 then RS-3. Not sure how old the tyres were though. I'd rather drive on Kumho than Nankang though lol.

RE050 are on a different (more expensive) level compared to the ones you listed. I had some second hand ones on the front of my R31, best street tyre I've ever driven on (RE040 aren't too shabby either).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Short answer: No. Medium answer: No, because you still need to conjure the things out of thin air to bolt them to a NA to make it a NA+T. Long Answer: No - The things you need to conjure - meaning a turbo, intercooling, manifolds, exhaust, intake/manifold/piping, clutch, injectors, fuel pump, AFM (?), ECU + Wiring (woo, N/A loom fun) have to come from somewhere. You could have many scavenged these things from an OEM car that someone had upgraded from and use some of these. This will be cost prohibitive now, especially so in the USA. You'd probably pay the same for newer, upgraded components that are better than old OEM stuff from 25-30 years ago. None of these big ticket items are re-usable for the N/A car. Why not buy new and upgrade while you're there? The only real consideration is turbo and fuel sizing and determining whether you want to stay within the bounds of the OEM engine or get into rebuild territory. These limits ARE lower with a N/A motor and especially N/A gearbox at the starting point. And if you're gonna upgrade those then you may as well consider having them built to begin with. Because everyone here knows you're never far from that next engine rebuild once you start making the power you want... The cars you see on the internet and SAU etc have been built over decades. If you're really clued in... you would sell your US car to somebody for what you paid for it. You would then scour AU JDM pages or SAU and buy a car like Dose's on this forum with your powerful American Dollar. This will save you so much money in the long term. Importing it could be tricky. Or it might not because USA. I have long said the only reason 90's Japanese stuff took off was because a) Japanese people had Japanese cars so that is what they used b) Australians could import these cars to Australia with very minimal changes and use them on the road here c) Neither country had well-priced access to US or EU Sports Cars. I don't believe the JDM scene would have taken off in Australia at all if we had EU priced EU BMW M offerings, or more especially the AUS V8 Scene would never have existed if we had the multitude of US cars like Camaros, Mustangs, Corvettes at the prices you folks do. After all - Do the math. I would say put a V8 in your R34 and that's the smart way forward. It is. I did it. I know this from my own experience. But at that point there's no reason to simply not buy a C5 or C6? It would be simpler and easier and cheaper and bette-
    • Reading all this... hurts lol. I have an ENR34 5MT and I paid an inflated USA price for the car alone, had to do tons of preventative maintenance past that, and so I'm over $30K USD into the car already and haven't even touched power.  I wanted to +t it. Not even trying to make GTR numbers, I'd be happy with 250hp.  Can I get away with paying much less to make that happen?
    • Damn you’ve done well, definitely snapping necks.
    • Great weekend and event. Open fire at the caravan park, perfect weather all day and a great feed and a couple of drinks at at awesome country pub.
    • Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
×
×
  • Create New...