Jump to content
SAU Community

Recommended Posts

I had a look through the ANDRA rule book for a checklist for what must be done once you run break into the ten second zone (10.999 or quicker).

Let me know if I've missed anything!

+ 1.4 Credentials: Need ANDRA membership and Unlimited Drag Racing Licence (UDL). To get a UDL you need to undergo a medical examination. You can download the forms for these things at the ANDRA site.

+ 1.7 ANDRA Log Books. Need to apply for log books and have a tech inspection on your racecar. You can download the form at the ANDRA site.

+ 2.3 Driveline. A tailshaft loop is required for cars 12.99 or quicker.

+ 2.6 Flywheel Shields/Bellhousings. Required to use a steel or titanum bellhousing or shield according to SFI 4.1 or 9.1. You can use a ballistic blanket instead if there is no commercially available steel bellhousing.

+ 4.6 Parachutes. If your car runs faster than 140 MPH a parachute must be fitted and deployed on each run.

+ 4.7 Roll Cage. Full cage mounted at a minimum of six points (or if faster than 140 MPH).

+ 5.2 Tyres. Quicker than 12.50 you cannot use radial fronts with slicks on the rear.

+ 5.3 Wheels. Must be fitted with open ended wheel nuts.

+ 6.2 Window Nets. Must be fitted between side and top bars on the driver's side.

+ 8.1 Batteries. Require a blue triangle to indicate battery location. If quicker than 11.99 you require a battery isolation switch located in the battery location maker.

+ 9.1 Technical Inspections. Require tech inspection every two years.

+ 10.8 Helmet. Adhering to Australian Standard AS 1698 1974/1988

+ 10.10 Protective Clothing. Require fireproof gloves, shoes, socks and a race suit adhering to one of: SFI 3.2A/5, FIA Norme 1986 or FIA Norme 8856-2000

+ 10.11 Harness. Faster than 130 MPH requires a five point harness with crotch strap. Quicker than 11.99 requires a four point harness.

  • 3 weeks later...
+ 5.2 Tyres. Quicker than 12.50 you cannot use radial fronts with slicks on the rear.

AHEM! :)

Dunno about this quicker than 11.99 bollocks though :(

Clint, dunno if the whole book is online - try www.andra.com.au

Adrian

What exactly is a tailshaft loop?

This is a loop of steel that surrounds the tailshaft in the event that it should break, snap, let go etc and keeps it from digging into the surface of the track and flipping your car many many times :)

Picture this, your tailshaft fails for whatever reason and drops out of the gearbox (or similar) and points straight at the tarmac while you're halfway through your run doing 100mph. All bad.

Adrian

front shaft loops = yes

drive shaft loops = no

Front and tail shafts in GTR's face in the direction of travel and therefore pose a roll-over risk. Drive shafts do not.

Adrian

whats andras standing on split tailshafts though?? it used to be you didnt have to have a loop on a car with a centre bearing, such an a skyline... Oh another interesting point was the harness one obviously they dont enforce this rule very often as there are alot of cars i see competing time and time again without a harness that according to the rule need one!!!

..

Oh another interesting point was the harness one obviously they dont enforce this rule very often as there are alot of cars i see competing time and time again without a harness that according to the rule need one!!!

Enforcing of the ANDRA rules at WSID seems to be inconsistent to me.

I got bounced 11/8/2004 for running slicks with radials on the front. I counted several other competitors doing the same thing who were allowed to do so by the same officials who pulled me up for it.

Anyone who runs 11.999 or quicker should have a four point harness, yet there are numerous competitors who break that rule.

On 12/6/2004 I ran against George in HYP10A when he ran 9.355 @ 145.44 MPH yet the car was not fitted with a parachute.

As for needing a tailshaft loop when you run 12.999 or quicker, how many times have the scrutineers jacked your car up to check?

The ANDRA rules are not enforced in a consistent manner by WSID scrutineers or ANDRA officials at the track. I think all the rules make sense and don't complain about any of them. But it's hard to swallow when the rules are enforced inconsistently, especially when you are on the wrong side of that inconsistency!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah pretty impressive hey, good to see quality products not over-shooting their prices. That's what drew me to buy the hypergear turbo, just a shame I've never got the chance to see it in action
    • Thank you GTSBoy and MBS206 I have done the compression test with the motor out of the vehicle, reason for the test was to see if I needed to remove the head and do rings etc while its out. I'm in the process of respraying the vehicle and tidying up a few things. Story behind it all is I've just purchased the skyline and it was running when I got it, never drove it on the street though as I wanted to pull it down and do it all up again before registering it. the gentleman I purchased it from told me the motor has a forged bottom end and has a decent tune through it but I was going to pull the sump off anyway to see if it is a forged bottom end. that's why I thought id do a compression test beforehand. 
    • Man, I'm kind of amazed that the price of the turbo has not changed in 7 years. Everything else is inflating beyond reason, but not this? Good on Tao / hypergear I guess? Anyways, good luck with the sale!
    • I'm selling my brand new, in the box, never used Hypergear ATR45 - and I had some additions I paid for a few yrs back when I purchased it. Never ended up having the rest of the money to add all the mods at once, so I just ended up slowly selling each part. I originally had it internally gated, with the dump pipe, however I found it was incompatible with what I was going to use it for, so I contacted (I think Ken) from Hypergear, and he and I messaged back and forth & he got me to ship the turbo back, where they modified it & made it externally gated, and gave me the 5 bolt dump pipe attachment for custom welding. (Photos below) This turbo like I said has never touched the inside of an engine bay, it's completely brand new, never used, been sitting in the same box it arrived in, covered in plastic & all. Below are the photos of it: And while the guys at Hypergear were making it in-shop, they sent me some photos of the process: I'm looking at selling this just because I'm in need of the money right now, and don't have plans on modifying the 34 anytime soon - and from reviews & peformance sheets, this turbo had amazing results back when I was researching. The turbo was purchased in 2018 for $1.9k, with the mods I got added on. Looking at the website now, for the same turbo they sell (ATR45SAT), with the current addons it adds up to $1830 for the turbo Current addons included: - Bolted dump adaptor - Ball bearing CHRA - Braided oil feeding line So I'm looking to possibly sell it for around $1800, with shipping included in that 1.8k, It cost me around $120 to ship - so yeah thought I'd throw it out there and see if anyone was interested in purchasing. Cheers!
×
×
  • Create New...