Jump to content
SAU Community

FS: RB25DET Neo stock bottom end - Needs inspection and rebuild

V28VX37
 Share

Recommended Posts

V28VX37 Veteran

V28VX37

Posted
Posted

Hi all, I've got my blown RB25DET Neo stock bottom end for sale:

  • Cylinders 3, 5 and 6 have lost compression and it appears that the rings are fused, however still rotates
  • Two of the bores (5 and 6) are scratched deep enough to feel when you run your finger over the bore, there are less severe scratches on other cylinders too
  • When the engine went it first started pushing a lot of coolant and finally went up heaps in crank case pressure and started blowing oil and smoke from the breathers
  • There are some burn marks near the water galleries on the recently changed head gasket (Oct 2016, included with the engine) but we're not sure if these were there before, during or after the bottom end went
  • I am not 100% certain of the root cause of the engine failure and there may be other damage to the block besides the bores 

This engine is off my 1998 R34 GTT sedan and was at 156,565km when pulled out, with the last 30,000 kms at around 275rwkw. The car was still movable when the engine was pulled but ran quite rough. Please let me know if you need any other information.

The engine is currently at my mechanic in Melbourne south east, pick up only.

What's included: Engine block, rotating assembly, head gasket, couple of other random gaskets. Possibly sump and oil pickup. I will keep the water pump. 

Asking $150 but open to offers. Note I will need buyer's driver license number for the receipt. Absolutely no warranty other than this might make a very awkward coffee table :)

Thanks guys

33519442535_7cf9851631.jpg


33478318966_3418004d7f.jpg


33390770031_f223281d63.jpg


33519442745_ee7d61f35f.jpg 


33390771121_83b5f41a11.jpg


33519443035_b3aefaa9f5.jpg


33519442035_de6972454f.jpg


33390769381_b794ff0a7a.jpg


32854345172_ff304aa54a.jpg 


33519441535_4b776edc87.jpg

  • Like 1
V28VX37 Veteran

V28VX37

Posted
  • Author
Posted

$100 if you come and pick it this weekend or next week, I need the space back.

I will even leave the sump and oil pick up on for you, so it should be good for those, crank, rods, engine mount brackets and perhaps the oil pump.

Neo goodness cheap cheap!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      New R32 owner soon

      By Duncan · Posted

      Yeah agreed, you can't assume that shop are they only people who ever had to work on it. It was just a guess on the mods based on how things were done back then. You can check the Air Flow Meters by the part number on their tags, they are likely either Z32 or Nismo ones (both read about the same but the Z32 one is a little larger while nismo is stock size but supports the higher airflow like a Z32). And yes, all that would get you to 450hp / 340kw To tell what is happening with the turbos, you want a photo of the tag on the core, that will say what it was made out of  (they can retain the front and rear covers to make the plumbing easier)  
    • bardabe
      1992 R32 GT-R Race Car

      By bardabe · Posted

      I'm selling my personal race car. 1992 BNR32 Skyline GT-R About eight years ago the engine developed the dreaded low oil pressure problem. I removed it and found the issue. However shortly after I moved half way across the country, moved my work shop, bought a house, got married, then moved my shop again to it's permanent location for the time being. in turn I do not have the time to race this car as it should be. In turn the engine I built for this car will end up in my street car and this car I hope finds a home with someone who can use it to it's full potential. The roll bar was built by Jason Noren Fabricaiton in Pomona California to SCCA and NASA Specs. The car used to compete in redline time attack and global time attack enthusiast class. It also has a fire suppression system.  The car is with me at my workshop in Kyle Texas, USA. Shipping it is no problem, I can personally deliver the car to the port of either Houston or Los Angeles. Any other port depending on where it is may require transport but we can always work that out.   The chassis itself is rust free, rear quarters and under fenders are free of any rust so it's a very solid foundation for anyone who wishes to move forward with it. As posted and at the asking price of $20,000 USD the car includes all of the following;   All OEM Body panels, front fenders, rear bumpers etc.  OEM Nissan Projector headlamps (Pictured N1 lamps were removed) OEM Nismo Side Skirts / Extensions OEM Rear Spats  Front & Rear Subframes are installed car is full roller Rear Subframe has Cusco Camber Arms, Whiteline HICAS Elimination Front Subframe has Whiteline tension rods and whiteline Sway bars w/ endlinks.  Buddy Club N1 Coilovers All chassis wiring and engine wiring is in tact. Attessa System is fully in tact and was functional before engine removal.  BCNR33 GT-R Brembo Brakes F+R with Endless MX72 Plus Pads, DBA Rotors & Stainless Steel Brake lines Billion Racing Radiator Billion Radiator Hoses Fluidyne Engine Oil Cooler Accusump System (trunk Mounted) 5 Speed Transmission w/ Transfer Case F+R Prop-shafts Rear Differential With rear Axles.  Nismo Gauge Cluster Nismo Clutch + Flywheel   Essentially what is needed to make this car running and driving again is as follows: A working Engine, an ECU, and time to put it together. The price posted is or best offer as I am willing to remove some components to accommodate price to a certain extent. If any serious buyer wants full detailed pictures, videos, or any questions I'll be happy to answer them. I believe this car is priced to move quickly considering it's a rust free and very straight chassis but always open to fair negotiation.  I can be contacted via phone or email. (+19517081648) email is [email protected]   
    • Kapr
      Oil pan for RB25DET NEO Stagea "version"

      By Kapr · Posted

      So...to my (and my mechanics doing the swap) surprise...the oil pan from NEO engine does not fit 100% and needs to by modified like this: It is not a huge problem but in the future i want a "proper" oil pan. So question is...what different oil pan can i get to fit without any problems and modification? Thanks! 
    • Rezz
      New R32 owner soon

      By Rezz · Posted

      Some more info I found.  These are the last entries Yoshikiyo Fujii made on his blog before he passed away in 2009: http://blog.livedoor.jp/fujii_dynamics/ And finally this is where the workshop was situated:  https://maps.app.goo.gl/HhTPtHzt3WVcBTiEA  
    • Keeper
      SAUNSW - Cruise - Albion Park Aviation Museum - 9th August

      By Keeper · Posted

      shit boxes, kids, and daily drivers are all welcome
×
×
  • Create New...