Jump to content
SAU Community

Recommended Posts

That's an expensive set of nice wheels. Don't spoil it by putting stupidly narrow stretched tyres like some people do!

Something like 285 35 may do the job. If the tyres stick out too much make the guards bigger don't shrink the tyres!

  • Like 6
Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7821762
Share on other sites

I ran 275x35x19 on my R34 GTR (work d9r 19 x 10.5 +15), which is mildly lowered. I couldn't go full lock without scrubbing on the inner guard linings on both sides.

I went down to a 275x30x19 tyre and used a heat gun on my inner linings. No scrub whatsoever now.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7822513
Share on other sites

9 minutes ago, OV33RR said:

275/35r19 there pretty big dont think id like to go bigger scrubbing as it is

I understand - but then why go 10.5 wide if your not going to put the appropriate tire on there.

The below is 10 wide with a 285 - see how the sidewall is square - surely that will give the car better turning and handling - please someone correct me if I'm wrong. 

IMG_1513.JPG

  • Like 4
Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7824201
Share on other sites

  • 2 months later...
16 hours ago, vxsr33 said:

From what i have read 275 or 285 is the recommended width for a 10.5 inch rim. 275 on a 9 inch rim isn't recommended as its too wide.

275 on 9in wheels are within the LVTA guidelines but the proof of the pudding is in the photos - OPs tyres are clearly stretched and the above 285s on 10 in wheels look just right.

Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7838260
Share on other sites

  • 3 weeks later...

I've got the same wheels offset etc, previously I had 275/30 no scrubbing now I have 275/35 19's nitto nt05 scrub the inner and outer guard. Then again mine isn't ride height, I wouldn't go anything thicker then the 30 series unless u want to do some suspension and camber work. My front is at 3 degrees camber to prevent my guards ripping again.

 

Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7841048
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...