Jump to content
SAU Community

Recommended Posts

That's an expensive set of nice wheels. Don't spoil it by putting stupidly narrow stretched tyres like some people do!

Something like 285 35 may do the job. If the tyres stick out too much make the guards bigger don't shrink the tyres!

  • Like 6
Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7821762
Share on other sites

I ran 275x35x19 on my R34 GTR (work d9r 19 x 10.5 +15), which is mildly lowered. I couldn't go full lock without scrubbing on the inner guard linings on both sides.

I went down to a 275x30x19 tyre and used a heat gun on my inner linings. No scrub whatsoever now.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7822513
Share on other sites

9 minutes ago, OV33RR said:

275/35r19 there pretty big dont think id like to go bigger scrubbing as it is

I understand - but then why go 10.5 wide if your not going to put the appropriate tire on there.

The below is 10 wide with a 285 - see how the sidewall is square - surely that will give the car better turning and handling - please someone correct me if I'm wrong. 

IMG_1513.JPG

  • Like 4
Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7824201
Share on other sites

  • 2 months later...
16 hours ago, vxsr33 said:

From what i have read 275 or 285 is the recommended width for a 10.5 inch rim. 275 on a 9 inch rim isn't recommended as its too wide.

275 on 9in wheels are within the LVTA guidelines but the proof of the pudding is in the photos - OPs tyres are clearly stretched and the above 285s on 10 in wheels look just right.

Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7838260
Share on other sites

  • 3 weeks later...

I've got the same wheels offset etc, previously I had 275/30 no scrubbing now I have 275/35 19's nitto nt05 scrub the inner and outer guard. Then again mine isn't ride height, I wouldn't go anything thicker then the 30 series unless u want to do some suspension and camber work. My front is at 3 degrees camber to prevent my guards ripping again.

 

Link to comment
https://www.sau.com.au/forums/topic/469878-19x105-te37sl/#findComment-7841048
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...