Jump to content
SAU Community

Recommended Posts

Well!

she moved under her own starter motor power yesterday!

by the looks of things I need the auto front driveshaft with a manual spline to get length correct. I'm about a inch off. 

IMG_1074.JPG

IMG_1075.JPG

  • Like 1
  • 1 month later...
On 02/05/2017 at 0:17 PM, XRATED said:

...progress?

Yeah nah good.

 

sorry guys been slow lately.... my rano blew a gearbox so bought another spare truck haha.

drove the 32 round the block with no turbo... ran like a sack... but SHE DROVE!!!!!

im now onto the long list of small shit..... will post updates with specific how I go at around issues as I come across them. 

So far we have. 

Desil pump
Desil lines
Turbo manifold
Turbo lines
Turbo
Altinator
Altinator brake booster
Hot pipe
Water pump
Heater pipes
Power steering pump
Power steering lines - res to rack - pump to rack
Radiator - brackets and pipes.
Bonnet support damage
Bonnet hinges
Battery - battery clamps - second battery in boot
Un-rangi the throttle
Thermostat
Glow plug loom
Speedo
Tacho
Water temp
Oil temp
Passenger mirror
Dash
Front seats
Door cards
Rear seats
Carpet
Cabin / boot flame plate
Centre console
Sills 
Drive shaft
Drive shaft hoops
Fuel tank cradle
Cradle seal
Fuel line hose clamps
Rear and front plate lights
Exhaust
Radiator over flow
Gearbox tunnel

and last of as is desil pump solenoid and boost cutoff. 

Un-rangi the throttle.

Nissan terrano TD27T auto throttle cable.

firewall backing plate needed some massaging to make it fit the r32 chassis. Little bit longer than what was needed. 

how ever one full throw on the throttle pedal moved the Dessie pump throttle from idle to wide open perfectly! 

 

Side note.... if I had a thermostat in my garage it would currently be sitting on F**king cold! 

IMG_1469.JPG

  • Like 1

So oil pressure.......

i obviously want want the factory gauge on my dash to work. Will try and see if a RB20de oil pressure sender fits in the td block tonight that would make the most sense then the guage would be calabraited for that's sensor assuming the TD runs pressure inside the ranges that the RB sender can guage, and the wiring is already there from the R32 chassis loom...

there was another thing, oh RPM. Apparently on the front of the desil pump is a crank angle sensor for this....... I am unsure.....

power steering will be back in a week after the doctor cuts everything to bits and makes everything out of braided... should look quite sexy ;) 

Desil lines to be moved. Hand pump and filter to be relocated to drivers side of engine bay removing over 3m of solid lines. Contemplating putting this in the boot but unsure on operation at this distance. Need to check. 

IMG_1475.JPG

  • Like 1
  • 2 weeks later...

Yeah boi!

slow going this week..... the mother ship (gold rano) decided to blow her 1st 2nd 5th and reverse as well as rear diff.... what a fun ordeal....

blew the motor in the parts truck.... she didn't like swimming..... 

turbo is now on skyline motor..... 

power slteering is done. Braided lines all round baby and short as shit. 600mm if any one is wondering. For all three lines. With res moved to left side of brake booster.

desil hand pump and filter moved to down beside battery spot. Nice short lines on that too....

might go see a engine builder in the next few weeks and see if they want to do something stupid with the blowen motor.... if it's fixable lol.

turbo fins on compressor side of skyline are absolutely rooted... but no play... so free boosting till the turbo blows it is haha 

IMG_1503.JPG

IMG_1505.JPG

  • Like 2
  • 2 months later...

So I hit a snag. Shit came up had to put this build on hold blah blah blah......

just got back from a 600km venture to pick up ANOTHER TD27T 4000k on it. 

In the mail from Auckland is a A/R .50 with a AR.63 compressor. T3t4, external 38mm gate, 

AND WAIT FOR IT.

coming from some were in the land of OI the dingo ate my baby, is a 10lb nitrous kit and all the shit to hook it up ;) 

 

  • Like 2
  • 2 weeks later...

I broke my truck again FFS. All three spare altinators failed within 12 hours ;(

on a side note how sick is this, got a call from the land of drop bears. NOS is 8 weeks ago as they ran out of stock ;(.

but. 

IMG_2007.JPG

  • Like 1

Props for giving this a go

This is the stuff that people usually only imagine or talk about on paper, but never actually do it just to see what would happen...because it seems crazy and pointless, so you never actually find out what would happen. And for that reason, this is cool. I'd have been interested to see what an RD28 would do, as it is a more squared off stroke and revs higher than most Diesel engines (based on the RB family anyway) - probably more suitable to the Skyline diffs. But fk it, this is more interesting because it makes less sense. Speaking of - what are you doing about gear ratios being short or does the Navara box take care of it?

Wish I had the crazy creativity and motivation to do stuff like this...

Quote

yeah i understand but i honestly dont consider the turbo to be a critical component in the car

BAHAHAHAHAHA I just lost my toys reading that ! 

The whole doing on pape bit is the part that make sure me giggle the most. (Not sure if you have see no my other post about a RB in a 4x4 D21 Navara but I feel you need to finding it ;) )

gear ratio: I don't know. Is the simple answer. I have the factory RB20de Manual diff in there. I don't even know I feel that will handle the torque increase. 

Navara td box has very similar ratio to the 4x4 one. So with 600+ NM we're expecting a very quick 0-100 time. After that she won't have the revs to go past 130 ( I imagine.)

got another gearbox to regear with 20det internals tho so it will be a wing and a miss. 

PROGRESS!!!!

new ( cough cough 400km) motor got dropped in. Annnnnnd turbo is too big ( wish some one would say that to me some nights ) off to the engineers my manifold goes. 

2 options turbo mounted in front of the motor with 2" custom manifold feeding it. OR very high top mount. Issue there is i loose my strut brace and that's is a no no.

fiber glass 25mm guards on the way.

fiber glass GTR front bumper on the way.

oil relocation kit on the way.

nitrous 6 week away.

IMG_2053.JPG

IMG_2055.JPG

IMG_2056.JPG

  • Like 3

Any one here watch house of muscle ?

go watch episode ten on YouTbe..... yummy.... 

so off came the sump that's the poor engineers problem now. Motor sitts so low in the engine bay I fear lowering I think as the sump is close to the ground. Future issues. Blahhhhh

how ever. Everything is just held in with rope to get a idea In my head. But what do y'all think  of this? 

IMG_2078.JPG

IMG_2081.JPG

IMG_2082.JPG

  • Like 1
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...