Jump to content
SAU Community

Recommended Posts

No oil reading and oil light flashing but has oil

So I have a weird problem where I have oil did the change about 2-3 months ago and now the dipstick isnt giving any reading when cold after wiping off. And when its cold after starting the oil pressure light comes on for a moment and does it randomly while driving not too often though. I know it has oil in it as it not puddling but yeah its got leaks. I put in another liter after seeing the dip bare but made no difference. So now I am not sure how to proceed and its my daily only one.

I have put another 500ml in and the light still coming on and still low reading. I will keep going when rain pisses off.

Had the car about 7 months always been funny with oil like heaps blow by and light coming on after oil changes etc. Has the no oil rattle when starting for a couple of seconds usually when cold.

Edited by HailDamage

where are you putting the oil in? does it have an extended or factory sump? if you run the car after topping up the oil and then open the radiator cap do you have a milkshake? is there a huge pool of oil under your car?

where are you putting the oil in?

Into the oil fill port on the intake cam cover (making sure to be specific)

does it have an extended or factory sump?

Factory and i have AWD motor if makes any difference

if you run the car after topping up the oil and then open the radiator cap do you have a milkshake?

No it looks normal.

is there a huge pool of oil under your car?

No there is a leak somewhere but its definitely no putting anything on the ground.

Stop guessing. Like Ben said drain the sump and see how much comes out. If it is new oil you can put it back in but make sure you put 5.5 or so litres until you see it on the dip stick. You say you have lots of blow by - what does your exhaust look like? You may be burning heaps. Do a compression test. maybe your engine is stuffed. If its not now it soon will be if you keep driving it with no oil pressure.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...