Jump to content
SAU Community

Recommended Posts

Hey guys so here are the technical specs

 

Rb25det series 2 neo manual

Fmic

Blitz pod

3 inch turbo back

Splitfire coil packs

 

Okay so the car runs fine for 10 mins and will come on boost fine and rev out though I only took it 5k as it was cold. This sputtering as if the traction control has come on the sound is like a limiter the same sound it makes when traction control comes on. Btw I leave traction co troll off because when it would turn on before it would cause knock and then the check engine light would come on. This problem has only occured after installing the splitfires. It happens no matter where in the rev range its just as soon as I got past vacuum and come on to positive pressure bit when it's cold it runs properly. The cars temperature gauge never comes up to halfway either I am replacing the thermostat not sure if this will fix it or if this is a coolant temp sensor.

 

If anyone has I had a similar cutting of power and popcorn sounding noise, point me in the right direction otherwise off to the shop.

  • 2 weeks later...

So I have replaced spark plugs, have splitfires and replaced coil pack harness but whenever I put a bit of load on the car it just breaks up, I'm thinking now to do o2 sensor as I get a misfire on idle, I replaced thermostat as it never comes up to temp but it must be the coolant temp sensor. Basically whenever I give it more than a qtr throttle it sounds like the fuel cut you get when traction control would kick in.

There's no boost leak sadly, I had a boost leak and fixed it car was running fine until the splitfires went in it hold boost fine as I said will go to red line, I'm really leaning towards a dud o2 sensor as it deals with load and I have terrible fuel economy

It will drive fine when the car is completely cold and drives perfect for 10 mins im thinking between the o2 sensor and coolant tempo sensor throwing out the afr I also cleaned maf 3 weeks ago when I found the boost leak

Hey guys I think I've found the problem ive got extreme regarding from the cas, or pre ignition and why my fuel economy is so bad as well I found that a dodgy coolant temp sensor can cause this on skyline owners forum

5 hours ago, zirbmail said:

Hey guys I think I've found the problem ive got extreme regarding from the cas, or pre ignition and why my fuel economy is so bad as well I found that a dodgy coolant temp sensor can cause this on skyline owners forum

Have you checked your sensor or just assume it is the issue?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...