Jump to content
SAU Community

Recommended Posts

  On 23/01/2019 at 7:39 PM, KiwiRS4T said:

Have a search and you will find out how to generate codes by shorting out a couple of terminals on the socket under the dash.

Expand  

Or buy a PLMS developments consult cable and download Ecutalk then never pay for diagnostics again.

Edited by Rusty Nuts
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/475919-scan-tool/#findComment-7897081
Share on other sites

Except for one thing.  ECUTalk only interrogates the ECU, not the other CUs on the Consult bus.  So to ask your ABS/TCS or HICAS ECU what is wrong with it, you either have to manually trigger the diagnostic mode, or use a proper scan tool.  Ask me** how I know that it is impossible to put a Skyline into HICAS diagnostic to find out the steering angle sensor is not working.

 

 

**Hint, the steering angle sensor is part of the song and dance routine used to put it into diagnostic mode!

Link to comment
https://www.sau.com.au/forums/topic/475919-scan-tool/#findComment-7897082
Share on other sites

  On 24/01/2019 at 5:48 AM, GTSBoy said:

find out the steering angle sensor is not working

Expand  

Gee and where in his question does he mention HICAS or are you mind reading again, comrade

Edited by Rusty Nuts
Link to comment
https://www.sau.com.au/forums/topic/475919-scan-tool/#findComment-7897085
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...