Jump to content
SAU Community

Recommended Posts

All,

so almost all tasks are complete for my remap.

 

what I have :

blitz fmiz

oil cooler(to install)

spitfire coil

iridium plug

walbro 255(standard wiring, need to do direct feed)

greddy profex boost controller

Extreme ceramic clutch and flywheel

Stock internal, no head gasket or stud change

 

to buy:

hybrid turbo capable of 450ps

ev14 injector

now after reading hours and hours of forum , i still don’t know what I can reliably get from my r34.

 

some tunner say max is 400ps while other say they can reliably get 500ps as neo is much stronger than r33 rb25

My view is I can get around 450ps on stock internal. Thoughts?

 

now trickey bit is, one tuner tells me I should use link g4 boost solonoid which i understand is closed loop rather than my greddy and another say doesn’t matter.

which one?

 

i like to be able to have a safe boost setting and loon mode so using greddy enables that rather than having a botton to flick it on ecu.

 

any advice or thought is much appreciated

Link to comment
https://www.sau.com.au/forums/topic/476029-r34-link-ecu/
Share on other sites

If you have a Link it makes sense to use it to control boost (with a Mac solenoid). You only need one boost setting (why would you have an unsafe one?). Limit boost with your accelerator.

Yes the Neo has GTR rods. 300KW should be fun.

Link to comment
https://www.sau.com.au/forums/topic/476029-r34-link-ecu/#findComment-7898128
Share on other sites

One of the tuners says he wants the car for few days whereas most tuners say if you come in morning it will be finished within 2-3 hours

 

i am just worried that if i leave the car, they start taking parts of it or break it to get business

 

i am not been pessimistic but think some mechanic do this unless they know you else how would they make money

 

reading on uk forums, both have similar reputations but one wanting the car for number of days to do dyno and also road tests seems little dodgy...

 

is he seriously going to spend 4 days on my car mapping it??

Link to comment
https://www.sau.com.au/forums/topic/476029-r34-link-ecu/#findComment-7898154
Share on other sites

Lol..

Scaling up all the sensors properly, checking all the inputs and outputs are setup correctly already takes up a couple of hours.

Then you'll need to spend at least 2 to 3 hours on the dyno followed by some road tuning to refine it.

Now.. say "if" you've setup all your IOs properly and setup all your transient, cold starts, hot starts properly then sure..  2 to 3 hours is fine. However, I have NEVER seen a car given to me that has been running properly. Every single one has had fuel pressure problems or IOs setup wrong or EBCs connected wrong etc.

Also it's a Skyline with some bolt ons, doubt anyone will pinch anything if they're a large enough shop.

Link to comment
https://www.sau.com.au/forums/topic/476029-r34-link-ecu/#findComment-7898156
Share on other sites

What did you mean by never given a car without problem?

 

well guy is charging me £400 for dyno and that is for 3.5 hours and around £200 for fitting

 

the way i understood, fitting is very simple, fit ecu in case, fit and wire air temp and fit maps/boost solonoid

Link to comment
https://www.sau.com.au/forums/topic/476029-r34-link-ecu/#findComment-7898158
Share on other sites

Just now, Ben C34 said:

Quick tune equals shit tune.

They need the car for a few days to make sure cold start is good. That's them caring. Otherwise anyone can slap a tune together and send you on your way, to have a car that starts and runs shit when cold..

Link to comment
https://www.sau.com.au/forums/topic/476029-r34-link-ecu/#findComment-7898161
Share on other sites

A good tune will take a total of up to 8 hours depending on the variables (adjustable cam gears etc). The tuner will want to keep it overnight to optimise the cold start and cold running. I have never heard of a tuner breaking things to create more work but then you are in England!

Link to comment
https://www.sau.com.au/forums/topic/476029-r34-link-ecu/#findComment-7898162
Share on other sites

3 minutes ago, Ben C34 said:

Anyone can slap a tune together and send you on your way, to have a car that starts and runs shit when cold..

Then blame the injectors and/or cams for the poor cold start, funny how many times I've heard this.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/476029-r34-link-ecu/#findComment-7898163
Share on other sites

To get a tune right, like fully, fully, fully, OEM-Spec right, will take many days and many minor adjustments. Like Dose Pipe said, it's not that people are terrible tuners if they can't tune a car perfectly in 2-3 hours, it actually takes a lot of time to get all the niggles and weird shit behaviour out of cars when you tune them.

Having it multiple days means they can experience (and tune/fix) many of the drivability things that occur while driving a car that is not 40-200kmh pulls at full throttle.

Link to comment
https://www.sau.com.au/forums/topic/476029-r34-link-ecu/#findComment-7898166
Share on other sites

1 hour ago, drifter17a said:

Cold start as testing the car when it starts up?

 

 

What do you think? Does your car get colder or warmer when running? It takes along time for an engine to be properly cold, like overnight.

  • Haha 1
Link to comment
https://www.sau.com.au/forums/topic/476029-r34-link-ecu/#findComment-7898172
Share on other sites

11 minutes ago, drifter17a said:

I am overly paranoid that mechanic may nick something or even blow up the engine 

 

i am not there to see what they are doing..

Sounds like  you need to sleep in the car while they have it. Check they don't blow up your engine. Best to book some time off work now and maybe hire a private detective to do surveillance also incase you miss something.

  • Haha 1
Link to comment
https://www.sau.com.au/forums/topic/476029-r34-link-ecu/#findComment-7898237
Share on other sites

Whilst I have this topic open,  my boost gets to 11 psi on occasions when car is cold and when warm, it does not pass 7-8psi no matter what gear and WOT.

 

i don’t have a compressor so have bought a 65mm end cap and did put a tyre valve in it. I am then wanting to use my tyre inflator to check for leak. Is that doable or the tyre inflator will struggle?

 

is it a boost leak in your view or more a turbo problem?

 

it could also be my walbro is not directly feed but i can’t see any link between pump and boost

Edited by drifter17a
Link to comment
https://www.sau.com.au/forums/topic/476029-r34-link-ecu/#findComment-7898243
Share on other sites

If anything, someone who wants to keep the car to make sure they do a good job is the person you'd rather trust.

In the grand scheme of things, the car is not extensively modified. You're more likely to blow the motor up driving the damn thing hard than in controlled situations like any decent dyno operator will have on a dyno.

You did say overly paranoid. Try to be less of that, or at least recognize you are being overly paranoid.

"Car is cold" Car shouldn't be on boost when "car is cold"

Do you mean full boost when car is warm but it's 20C outside, vs same conditions but a 45C day when it's hot as f**k?

Link to comment
https://www.sau.com.au/forums/topic/476029-r34-link-ecu/#findComment-7898266
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
×
×
  • Create New...