Jump to content
SAU Community

Recommended Posts

Hi all.

Recently had my 350GT (purchased 2 months ago) serviced and was told I had the following issues with approx. prices to have them fixed:

* Rear brake pads (estimated approximately $180)
* Inoperative high mount stop lamp (estimated approximately $250 repaired/ approximately $190 second-hand)

* Front lower control arms (estimated approximately $800 for both sides)
* Worn rear sway bar links (estimated approximately $250 for both sides)
* Worn rear wheel bearings (estimated approximately $1100 for both sides)

How are the prices on these? They seem excessive but just wanted someone with knowledge to validate it for me.

Cheers!

 

 

 

 

 

Edited by jsmit94
Link to comment
https://www.sau.com.au/forums/topic/476814-work-to-be-done-on-my-350gt/
Share on other sites

Did they say what's wrong with the front control arms? Could the bushings just be replaced for a lot of those?
SuperPro/Whiteline make a lot of bushings for V35.

Some of those prices seem a bit steep, depends on if they're using OEM parts and what their hourly rate is for labour.

1 hour ago, Leroy Peterson said:

Did they say what's wrong with the front control arms? Could the bushings just be replaced for a lot of those?
SuperPro/Whiteline make a lot of bushings for V35.

Some of those prices seem a bit steep, depends on if they're using OEM parts and what their hourly rate is for labour.


 

Well he said that the bushes were 'broken', and then he said the whole control arms need replacing. 

The cars steering pulls pretty badly to the left, is this a symptom of that?

Edited by jsmit94

The brake pad price is fine, for decent pads + fitting.

The highmount brake light price could be fine or it could be ridiculous.  Depends on why it's dead, what needs to be replaced.

i concur with Leroy that the rest of the prices look a bit mad.  I wouldn't expect to pay that much for the rear wheel bearings.  Maybe half that, maybe a bit more than half. The control arms almost certainly don't need to be replaced.  New bushes.  The ARB links can't be that expensive.  I just put 4 onto my car for less than that.  The most expensive Whiteline ones are only ~$150 and they take 15 minutes to swap on the hoist.

Holy shit that wheel bearing price....

I just had both the rears done on my v36.. $250 for brand new ones shipped and $220 for installation. 
$1100 is insane.

Rear brake pads you can do yourself (unless you prefer not) and save the labour cost.
 

2 hours ago, The Max said:

Your mechanic is (figuratively) a rapist. Find someone either honest or who actually knows how to fix cars with the right amount of effort and parts.

yeah seems like it now.. Thought I could trust someone who says they have worked as a mechanic in Japan, says they specialise in Jap imports and actually sources parts through their Japanese business to not rip me off, considering the experience they have. Does anyone have any recommendations for someone to go to in Sydney? 
I'm from around Bankstown, so anywhere closeish to me (an hour away max) would be awesome.

Edited by jsmit94
8 hours ago, jsmit94 said:

yeah seems like it now.. Thought I could trust someone who says they have worked as a mechanic in Japan, says they specialise in Jap imports and actually sources parts through their Japanese business to not rip me off, considering the experience they have. Does anyone have any recommendations for someone to go to in Sydney? 
I'm from around Bankstown, so anywhere closeish to me (an hour away max) would be awesome.

To be honest dude my local ultratune services mine. Majority of 350z parts will fit your car so any mechanic will do it fine.

  • Like 1

Go to Adrian's Auto Centre at 100 Parramatta Rd Croydon. The workshop access is in the lane behind the car dealership. He's the guy I go to when it's not something I can do in my own driveway. No, he doesn't charge dealership prices and definitely runs an honest workshop.

11 hours ago, jsmit94 said:

yeah seems like it now.. Thought I could trust someone who says they have worked as a mechanic in Japan, says they specialise in Jap imports and actually sources parts through their Japanese business to not rip me off, considering the experience they have. Does anyone have any recommendations for someone to go to in Sydney? 
I'm from around Bankstown, so anywhere closeish to me (an hour away max) would be awesome.

I've been working on Japanese cars for over 25 years (I'm 30), I can source parts directly from Jesse Streeter (who lives in Japan) and partsouq (UAE).

Don't believe everything people say.

I sorted the high mount stop light on my old 250GT for $12.50 plus my own time - bought a Red 12 volt SMD LED strip from eBay, mounted it to a piece of black plastic and glued the whole thing into the existing housing. Looked great, worked great, passed inspection with zero issues

1 hour ago, niZmO_Man said:

I've been working on Japanese cars for over 25 years (I'm 30), I can source parts directly from Jesse Streeter (who lives in Japan) and partsouq (UAE).

Don't believe everything people say.

I guess it was more the reviews on their business that made me believe them, didn't expect someone with such good reviews to be so overpriced lol. I don't doubt that their work is good, but price-wise I think I will go elsewhere.

On 4/29/2019 at 3:15 PM, DashyyPC said:

Holy shit that wheel bearing price....

I just had both the rears done on my v36.. $250 for brand new ones shipped and $220 for installation. 
$1100 is insane.

Rear brake pads you can do yourself (unless you prefer not) and save the labour cost.
 

Where did you order the bearings from?

21 hours ago, fatz said:

Cofff have whole rear hubs in Sydney for a slab of beer

 

cooooofffdddd

haha I appreciate the offer man but because this car came with no evidence at all of any work that was done to it, i'd rather go to a place where I can get a tax invoice to show for it. Thanks anyways legend ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
    • Sorry, just assumed that talk of coloured pads meant EBC red/green/yellow/shit stuff. I don't know the DBA pads, but it's a reasonable bet that they will be OK. DBA make good stuff generally. Those 4000 series rotors I linked to are very good. I may well replace the RDA rotors I have with those when required.
    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
×
×
  • Create New...