Jump to content
SAU Community

Installing vq25det turbo setup on vq35de

NicPM35
 Share

Recommended Posts

NicPM35 Collaborator

NicPM35

Posted
Posted

I know I know I know, this topic has been covered before, but not in enough detail I reckon. 

I have a crazy idea, grabbing all the turbo bits off the vq25det engine and whacking them on my vq35de. 

Some have said the turbo would be too small, but does that mean it just wouldn't make huge power or would actually just get blown to bits? And would a high flow turbo work better then?

I'm not interested in huge power, just a nice little boost up from stock. 

Seems silly to spend 10k on a turbo kit, when vq25det setups are right there... 

Tell me I'm dreaming 

30ed32 Enthusiast

30ed32

Posted
Posted

The 25 turbo would be too small, I have turbos from my vq30dets and even those would be too small for a 35 and I would guess the 30 turbo is bigger than the 25.  You can get high flowed vq30det turbos though that are so called rated for 400hp on a 30.  Could still use the rest of the turbo exhaust piping.

iamhe77 Grand Master

iamhe77

Posted
Posted

Got a mate selling his HKS turbo kit with Stillen exhaust which should bolt up on a PM35. Nowhere near $10k.

 

VQ25det plenum has very small runner holes compared to the VQ35. Not even close to matching up.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

An inline VH45de from a Fuga or something like the below would give you some grunt:

https://www.trademe.co.nz/motors/car-parts-accessories/nissan/engines/listing-2154613139.htm?rsqid=b1d4fc303ef64319b70facb103b34613-001

Jetwreck Grand Master

Jetwreck

Posted
Posted

It's not just the turbo kit. I've done about 4 or 5 of the VQ35DE turbo conversions ranging from 240AWKW to 660RWKW. Your supporting mods will be just as expensive as a HKS turbo kit to do it properly. If you do it yourself you will save big $$$.

 

IMO the best bag for buck on the street if you want approx 200RWK on a VQ35DE is a firstly a very well sorted and flowing exhaust with H/F CAT's(use Z34 headers and cat's), a Z33 manual diff(3.538) for those of you with the PM35 only as the PNM is already 3.538, fuel pump and good catch can setup. With those mods you should be able to get 180-190RWKW with good plug and play ECU like a LINK.

If you want more for a street car a supercharger is your next best bet. The supporting mods to make it work well and get you reliability. power will be about 220 - 240RWK.

Once you go turbo its a major game changer as everything needs to be adapted especially if your in the PNM35.

P.S. I am only talking figures with 98 Octane fuel for the boosted setups as E85 is another setup and power change. IMO is you have $20K put an LSA in it and say goodbye

 

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
7 hours ago, NicPM35 said:

Latest plan: give wife the car and just buy a faster car. Problem solved. 

Good idea. I was going to suggest selling it and getting the best RS6 you could afford.

NicPM35 Collaborator

NicPM35

Posted
  • Author
Posted
1 minute ago, KiwiRS4T said:

Good idea. I was going to suggest selling it and getting the best RS6 you could afford.

Oof $$$$. I'm looking at importing a jzx110, still not the best bang for buck, but hard to beat a nice 4 door 1jz!

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
2 hours ago, NicPM35 said:

Oof $$$$. I'm looking at importing a jzx110, still not the best bang for buck, but hard to beat a nice 4 door 1jz!

Yep I had a nice Cressida 2.8  many years ago. I was just about to change my Skoda Superb 2.7 for an Audi Allroad 2.7TT when I got to the bit where it said to service the turbos first remove the engine so for now I have settled for a boring but reliable (almost beige) 2005 Camry V6

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      Whoops!
×
×
  • Create New...