Jump to content
SAU Community

Recommended Posts

Hey All,

I have checked the forum but just get a heap of for sale posts. I know the pros and cons of raising the boot rear but I had a few other questions. 

- should I use a spring washer and if so, where exactly in relation to the hood and hood plate and other washers?

- should I use a rubber/nylon washer and if so, where in relation to the hood and hood plate and other washers?

- should I stagger the number of spacers between the front and rear hood panel bolts so that they keep the angle of the bonnet or mount flat on the same number of washers for both?

- should I take the coil pack cover off in addition and if so where is a good spot for the igniter?

 

Thanks guys. 

Btw I have just changed gearbox and rear diff oil to redline lightweight and motul gearbox competition - best money I have spent on the car so far wow!

 

It's not 1975 any more. Why would you want to do this? You do appreciate that the base of the windscreen is a high pressure area, not a low pressure area, and the whole idea behind lifting the rear of the bonnet to let out out of the engine bay is invalidated by that fact? Right?

And don't take the coil pack cover off. Look inside the back of the timing cover. See the slots there? There is actually a deliberate effort made by Nissan for the cam drive system to pump some air through the coil tunnel. Take the cover off and you lose that. And you have to find some other method to mount the ignitoe, which you wouldn't have to do if you didn't remove the cover.

If my Splitfires die, and I don't feel like spending ~$1k for R35 type coils, the Yaris coils would be what I would do.

They are better coils, but not massively better. The R35/Audi/etc coils are quite a big step up though.

And, don't be fooled by the kits that say "Genuine Bosch Yaris Coils". The coils may be made by Bosch.....but genuine Yaris coils were made for Toyota by Denso. The Bosch ones are effectively aftermarket. I can't tell you that they are as good as the Denso ones.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Resizing injectors in Nistune can be done a couple of ways, and there are a couple of ways that you can make a mess of it. The tuner needs to be really aware of the effects of whichever approach he uses (either K, or TIM). They are both easy enough to "get the injector size right" to run the engine. But little details like old start enrichment and hot start are affected differently, depending on which boxes you check.
    • Pretty safe to say almost everyone that has tuned their own car has experienced this issue. The difference being that we have our laptop in the car and when it happens, it's literally 10 seconds of tuning to sort it.  Would you be happy to plug in your laptop and sort this yourself? It is a very simple process and there is no risk of harming your engine (if you are worried about that). 
    • Yeah thats the next step now, either they wil or i will take out for a drive to work and go straight their after work and see is we get the same issues 🤞  thought i try my luck here too, never know someone else might have had the same issue but thanks for the reply 
    • Basically your tuner needs to drive it for the 30 min (or whatever) to create the same conditions then check the ECU settings and sensors at that time. They may not be excited to because that takes them 30 min rather than just opening the bonnet and seeing the problem straight away.... Hot start is generally not as tricky as cold start, but there would be a table for fuel enrichment vs coolant temp as a starting point
    • Yeah, they all cant say anything for sure as everything is working fine . Said unable to find an issue untill it stops again. Could mist likely be CAS wiring or IAS valve issue but again not 100%
×
×
  • Create New...