Jump to content
SAU Community

Recommended Posts

1 hour ago, MoMnDadGTR said:

sorry for double post, but could try blocking pvc system and running a catch can setup to see whats going on, may be a waste of time tho...just to clarify are you running a sr20 or an rb in your car? I had a integra type r once with a b18c5 it burnt 1 litre of oil to 3 tank of fuel but would smoke like absolutely crazy from the exhaust blue. I feel like if your rings were shot it would smoke quite a bit more than just on shifts.  valve stem seals m8 or something weird internally maybe.....rebuild the engine and slap  a new turbo on it start fresh.

its a sr20. I don't imagine it would have something to do with the intake manifold if I forgot to connect something. but can't imagine it would be. Was thinking of resetting the ecu . What I did is put the plumbing back to stock cause the previous owner messed around with it a bit but the blow off valve or whatever the PCM is loud as hell when shifting gears lol.

1 hour ago, KiwiRS4T said:

Pretty sure you can do the valve stem seals without taking the head off. They are cheap - give it a try.

Yea I seen the pliers but the procedure is confusing. It makes sense for the first cylinder how to do it put the rope down, put piston to BDC then put it out with the compression tool, etc. but everyone seems to do it with the timing chain or belt REMOVED when rotating the crank pulley. wont this make the valve hit pistons?

10 hours ago, GTSBoy said:

No cams installed = ........ [you complete the sentence].

No idea what it is lol. Is it that valves ca t open or close if cams removed?. At tdc are ALL valaves on ALL cylinders closed?

Edited by silviaz
1 hour ago, silviaz said:

No idea what it is lol. Is it that valves ca t open or close if cams removed?. At tdc are ALL valaves on ALL cylinders closed?

If  the cam is on the bench I don't see how it could push a valve open

 

 

 

3 minutes ago, silviaz said:

crank can push the piston to hit the valve

The crank would have to push the piston all the way through the combustion chamber and into the valve seat area to hit a valve that is closed and cannot be open because there is nothing (no camshaft) to push it open.

Close eyes. Picture inside of engine.

5 hours ago, GTSBoy said:

The crank would have to push the piston all the way through the combustion chamber and into the valve seat area to hit a valve that is closed and cannot be open because there is nothing (no camshaft) to push it open.

Close eyes. Picture inside of engine.

Ah ok. I csnt find to find any COMPLETE guidea on this valve job. Know where i can find one?

37 minutes ago, silviaz said:

Ah ok. I csnt find to find any COMPLETE guidea on this valve job. Know where i can find one?

Don't do it. If you need a complete hand holding through the process get someone to do it . I would seriously doubt a complete guide for your engine on how to replace valve stem seals exists, (and it isn't required. Its same

concept regardless of anything)

16 hours ago, Ben C34 said:

Don't do it. If you need a complete hand holding through the process get someone to do it . I would seriously doubt a complete guide for your engine on how to replace valve stem seals exists, (and it isn't required. Its same

concept regardless of anything)

Yeah I think you're right. I can't visualise the whole process and if I can't it's probably a bad idea for me.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...