Jump to content
SAU Community

Recommended Posts

Fark, my phone keeps farking up the formatting when I type in forums, and only forums

 

I cannot be trusted with any electronics more advanced than a XBox 360

 

 

 

 

23 hours ago, The Bogan said:

I've got a ODB2 scanner that monitors IAT, and stuff, a up/down button is simple to work and easy to install

What I really want is a Haltec ecu thing is that monitors/adjusts everything, but, for the car it is overkill and costs way more than this old rooster can justify to purchase, wire in and then retune

Maybe if I win lotto 😒

HPTuners :D

But it is a flashed based ECU. Can't modify settings on the fly.

(actually you can but it's only certain OS's that do not support E85, so maybe you can)

The thing that put me off the varex thing is you obviously sacrifice your ODB2 port for it. I don't doubt that someone smart with a Haltech/Motec/ExpensiveECU could mimic the behaviour by sending X volts when Engine parameters = ABCD which would then activate the stepper motor...

  • Like 1
13 minutes ago, Kinkstaah said:

HPTuners :D

But it is a flashed based ECU. Can't modify settings on the fly.

(actually you can but it's only certain OS's that do not support E85, so maybe you can)

The thing that put me off the varex thing is you obviously sacrifice your ODB2 port for it. I don't doubt that someone smart with a Haltech/Motec/ExpensiveECU could mimic the behaviour by sending X volts when Engine parameters = ABCD which would then activate the stepper motor...

Why is it sacrificing an OBD2 port?
Just get an OBD2 Y Cable.
It can leave a factory looking OBD2 port where it normally would be, and leave an OBD2 cable plugged in elsewhere.

Secondly, you can splice into the CANBus cables if you want to.

There are also some low cost options out there that can listen to CAN signals, and then trigger IO ports that you wire to. The Ford guys use these a lot. One of them can also do it the other way of you flick a switch, and it'll send specific CAN messages. Lets the Ford guys do things like get all the dashboard, and light integrations working properly.

  • Like 2

The only time it will be closed is at home, for start ups and returning late at night, or, if pulled over by the constabulary for breath tests and stuff

 

So no need for anything fancy, just easy and reliable, fully open or fully closed

 

The neighbours have a new baby, I don't want to be "that neighbour" leaving for work, or coming home late

 

4 hours ago, Kinkstaah said:

HPTuners :D

But it is a flashed based ECU. Can't modify settings on the fly.

(actually you can but it's only certain OS's that do not support E85, so maybe you can)

The thing that put me off the varex thing is you obviously sacrifice your ODB2 port for it. I don't doubt that someone smart with a Haltech/Motec/ExpensiveECU could mimic the behaviour by sending X volts when Engine parameters = ABCD which would then activate the stepper motor...

Haltech make it really easy to do with one of these boxes - 

https://www.haltech.com/product/ht-038009-dc-motor-driver-dcmd/

Not recommending it for this circumstance, but it is a sexy piece of kit. 

  • Like 2
  • 2 weeks later...

Got the 4" Varex fitted. Nice and quiet closed for keeping neighbours happy early morning and late at night, nice and loudish open to keep me happy, basically has the same sound open thru the rev range as the old 4" it replaced. Put the momentary switch on the cover for the interior fuse box cover, nice and easy to get to. Mark is happy

20230222_144643.thumb.jpg.4e9da1e4a0c9b9ab56976e09a48bbc2a.jpg

  • Like 4

The suspension is set to stock FE2 height and so far hasn't scrapped on anything since the 4" system was fitted, and the car has seen all sorts of speed humps and steep driveways

  • Like 1

Stuck in 6 ltrs of fresh HPR5 and a filter, then cleaned up all my tool boxes.....and found the new door strikers I grabbed a while ago, so I fitted them up, remembering to do one bolt at a time so the bracket inside didn't end up lost in the sills to rattle around forever and make Mark sad, no more door clunks going over bumps is noice, it's basically a new luxury car now 😂

 

 

 

 

 

 

  • Like 1
  • 3 weeks later...

Took the car to Supecheap to get some bissell carpet cleaner liquid stuff for my.......ummm, bissell carpet cleaner, I'm going to do the interior again this weekend and the little bissell works a treat cleaning carpet, seats and trims, I did the usual walk around for "random" "stuff" and saw that Penrite 20w 40 full synthetic 6 litres was on sale for $48, bargain (nearly half price), the LS1 in the VX loves that 5hit every 5k km, so the car got enough new blood and oil filters for the next 2 oil changes, which are still 4500 km away.

Prior Preparation Prevents Piss Poor Performance 

I also grabbed 4 litres of Penrite MC 4ST V Twin 20w50 (again on special) for the engine, and a new filter, the engine and new filter only takes just on 3 litres, but, I have put on that air to oil cooler with adds about 0.5 litres to the fillI, I also got a litre of Penrite 80w140 Pro Gear for the transmission.

I've still got about 1 litre of Screaming Eagle SYN 3 20w50 that I will stick in the primary.

The bike will have its 3 holes filled 🤣

  • 2 weeks later...

Checked the wear markers on the R888R and found they were getting close, maybe another 2-3k km or so, so went shopping, I decided not to go the R888R again as I only got them to help at the drags, but they weren't really much better than the RS4's at the strip, the drag radials though are ace as expected

I was able to find some RS4 255/40 17 that were in stock to throw on the rear, but unfortunately there is no RS4 235/45 17 in stock anywhere in......Australia, so I got them to put me down for a pair when they arrive, they said it could be a month or two at least before they get any into Australia....bugger

So, they got wrapped in shrink wrap and stored next to the drag radials with are also wrapped in shrink wrap waiting patiently for their next outing

20230405_143904.thumb.jpg.8847d5ae190bd360d7c6b6b39e2259e4.jpg20230405_144943.thumb.jpg.f8b0b87794d8fef805b0d46de1f8f5a4.jpg

  • Like 1

The daughter has purchased a new Kia Cerento GT hatch, delivery is in August, sooooo, in August I am getting back the little Yaris YRS for a daily hack, it is the "big block" 1.5 ltr engine with the 4 speed auto, so you know it is.......slow as 10 slow things.

But it is a clean and well maintained little thing, that uses alot less fuel than both the Dunnydoore and the Harley for local trips.

Plus, leaving it parked at the local shopping centre will be alot less stressful, rain, hail or shine.

Yes, I am already looking for some 2nd hand rims and some lowered coils for it.

 

12 hours ago, The Bogan said:

The daughter has purchased a new Kia Cerento GT hatch, delivery is in August, sooooo, in August I am getting back the little Yaris YRS for a daily hack, it is the "big block" 1.5 ltr engine with the 4 speed auto, so you know it is.......slow as 10 slow things.

But it is a clean and well maintained little thing, that uses alot less fuel than both the Dunnydoore and the Harley for local trips.

Plus, leaving it parked at the local shopping centre will be alot less stressful, rain, hail or shine.

Yes, I am already looking for some 2nd hand rims and some lowered coils for it.

 

Manual swap time?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...