Jump to content
SAU Community

Recommended Posts

DIY:
Hicas ball joint removal & replacement / Gktech lock bar install.
 
Job:
Replace worn out hicas ball joints, without removing hubs.
Fit hicas lock bar.
 
Parts needed:
Gktech lock bar
2x Hicas ball joints

cover1.jpg.20a002e907dda38573d396804fc43bc0.jpg
 
Tools needed:
Jack, Jack stands, WD40, Grease, Impact wrench, Adjustable wrench, Socket set 10-30mm, Circlip pliers, Pliers, Ball joint press kit, 42mm O.D. x 37mm I.D. x 60mm Steel pipe, Pitman arm tool, Angle grinder, Breaker bar, Safety glasses, Hearing protection, Mask.
 
Duration:
3-6hrs.

Difficulty:
Medium - Easy with the right tools.
 
 
Step 1:

Remove rear seat, remove battery earth and remove suspension.

Then carefully jack up the car and use jack stands.
 
46.jpg.c1264be76a2dd92d6433120d3a01c36f.jpg
 
 
Step 2.

Spray wd-40 on the bolts, remove split pin and 17mm nut from ball joint/tie rod end.
 
45.jpg.d1a215e11323e96e06b9c6776cb58cf2.jpg
 
 
Step 3.

Use pitman arm tool or suitable tool to remove tie rod end.
 
44.jpg.146c7967e09de8892e1afce1f51a31c2.jpg
 
 
Step 4.
 
Crack the tie rods from the hicas unit under the rubber boot, unplug the hicas wiring.
 
42.jpg.87217dc8f77e261f4c37dbe310fa7856.jpg
 
 
Step 5.

Remove the 19mm bolts holding the hicas unit to the car and then remove the tie rods.
 
41.jpg.8f12ecf70e1e4961f239117522aa196c.jpg
 
 
Step 6.

Install the tie rods into the gktech lock bar leaving the rubber boots loose. 
 
21.jpg.060ab13cda0d3fe4688be725f4fe931d.jpg
 
 
Set that aside for now. 
 
 
BALL JOINT REMOVAL.
 
cover2.jpg.9f328d717179f063ce6386c651aa76e5.jpg
 
 
Step 7.
 
Remove circlip from back of ball joint.
 
22.jpg.1b1e2a8c3aa19e474f2dd251725d1f07.jpg
 
 
Step 8.

Cut the ball joint stud to allow more space to remove.
 
31.jpg.4da77c9d3ea780a99245f0617b4658ff.jpg
 
 
Step 9.

If you haven't removed suspension do it now.

Use the ball joint press tool to press the joint out.

Most kits don't come with a small enough size pipe to allow for extraction of the joint, so you will have to find a steel pipe of 42mm O.D. x 37mm I.D. x 60mm. Very common pipe size fits perfectly.
 
33.jpg.c80b4ef37a4b6d48e9fe3c741ac03697.jpg

Carefully align your press tool with the pipe on the hub. I used 5mm steel plate as a backing plate and then used the correct size socket to sit flush on the back of the ball joint. This will allow you to push the ball joint through the hub towards the rear. 

32.jpg.4453cb004c6e5202c1404e9ddfb48ca0.jpg
 
 
Step 10.
 
With the ball joint removed, clean the ball joint housing with wd40 and a rag.

30.jpg.145ab309f2456b91493ad44196d67555.jpg

 

Step 11.

Apply grease to the joint and housing.

6.jpg.7e1c01ebeee3c18f195db0d57390b8c9.jpg

 

Step 12.

Use a 30mm socket or similar sized pipe that fits over the rubber boot and sits on the metal rim of the joint to press the new joint in.

8.jpg.3e20d60c0035fa37a7cd8809ffca3912.jpg

Align the press tool with the socket and ball joints rim and start to turn the press tool to insert the joint into the hub.

27.jpg.36e87d900ad9d15d78cbfb6cca0d5e2e.jpg

4.jpg.d374f661c313aa5183176ff341c8ae6a.jpg

3.jpg.2d1eae626d6565bc66af6c4d297626ae.jpg

Joint installed.

23.jpg.b3d8281b8863d529745aeec374f1360d.jpg

 

Step 13.

Reinstall the circlip to the back of the ball joint.

22.jpg.1b1e2a8c3aa19e474f2dd251725d1f07.jpg

 

Step 14.

Cable tie the hicas wiring out of the way.

20.jpg.54159fc3969083e63a3d7e157a95d9fc.jpg

Install the gktech lock bar.

14.jpg.baf0038ee483d1d5c1d842fbc83a1434.jpg

Tighten the 19mm bolts. Check the tie rods are tight, then secure the rubber boots.

19.jpg.44e322758b6658db5bbfa8c01331ef15.jpg

 

Step 15.

Install the tie rod ends and replace the 17mm nut and split pin.

1.jpg.f36faaaf78b6537d1c25b06ecd39fd6f.jpg

 

Step 16.

Reinstall suspension, rear seat and wheels.

Remove hicas bulb on the cluster, or cut hicas warning light wire on hicas cu in boot.

Get wheel alignment.


All Done.

Edited by dyl33

Mental notes;

  1. The above is valid for electric HICAS, like 33 & 34. Not same same for hydraulic 32 HICAS.
  2. I shudder when I see chassis stands under the rear end of the chassis rails. It's too far forward for a stable support and it puts a lot of leverage from the mass of the rear of the car on the contact points and drives dents into the chassis rails. I prefer to locate them carefully under the subframe.
  3. ...
  4. Otherwise. Good.
  • Like 2
6 minutes ago, GTSBoy said:

Mental notes;

  1. The above is valid for electric HICAS, like 33 & 34. Not same same for hydraulic 32 HICAS.
  2. I shudder when I see chassis stands under the rear end of the chassis rails. It's too far forward for a stable support and it puts a lot of leverage from the mass of the rear of the car on the contact points and drives dents into the chassis rails. I prefer to locate them carefully under the subframe.
  3. ...
  4. Otherwise. Good.

1. Correct.

2. I'll take note. There is 4 stands under it, the blue 2 are on the subframe. 

3. ...

4 .?

  • 2 weeks later...

I wasted so much money on the Frenchy's Performance Garage tool. I'm sure it's great if your balljoints are in good condition, but I ended up stripping the coupler nut, and bending the threads on the balljoint trying to use their removal tool. 

I basically ended up doing the exact same thing as this guide to remove mine, and they came out like butter.

I used a torch to heat the knuckle up for around 60 seconds, and I used my 36mm axle nut socket as the retainer. I then used a thick washer on the back first, before putting a 14mm socket on the back to push it the rest of the way. This process took about 15-20 minutes per side, compared to the hours I spent trying different methods. Using the 36mm socket it has the dpeth that you don't need to grind the end of the balljoint off either. 

3e6b37ef690ce0179ebb33414a7e01bb.jpg

Edited by Jarsky
  • Like 1
  • 7 months later...
1 hour ago, Bart Japan said:

Does anyone know how to do a 32? Do you get a fitting that recirculates the HICAS?

If you don't want to remove the lines, I'm selling this spare kit.

134044532_10159572282190400_5239933425189596540_n.jpg.a37065c2d7f4799d69fc20317d281bf5.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sorry to hear your HFM BM57 was faulty,  did you contact HFM I would hope they would be at least grateful for the information if there was some sort of manufacturing fault, you would hope they would be sympathetic even if your item was 2 years old if it had never been fitted. May I ask where it leaked from ?
    • Cats are called Bella, and Donna...  Like that poisonous plant And I remember your 2 monsters, I remember making a little bit of wee when you let them out... LOL I have already installed cat doors into the laundry where their kitty litter is, and the sun room, apart from the cat doors there's not going to be any permanent mounted stuff on the interior walls (interior doors are cheap and easy to replace) I will get a outdoor cat cage thingie once I finish the landscaping out back... https://catnip.com.au/ The only off limit areas are the main bedroom and the gym room....but, currently the cats are curled up in bed, in the main bedroom with the Mrs.....LOL, the off limits for the kittens to the main bedroom lasted about 5 minutes with Jackie I currently only have 1 free standing huge cat tree multiple level scratching post thingie in the lounge room, but, I will be getting another one soon now that I'm happy with the furniture layout in the back room and have a perfect spot for it  
    • All of this is making it seem clear that running the Coppermix twin was definitely the way to go, especially in hindsight with how insane tariffs have gotten and the strength of the USD vs yen at the time.
    • That sounds like no chance of even importing one for road registering then Now I see why Duncan wants to check LHD rules for Targa...   I wonder how "bolt in" the AWD would be if you got one imported from the US and swapped it to an AUD one
    • Not to mention they drive like a bucket of bolts! yuck!
×
×
  • Create New...