Jump to content
SAU Community

Recommended Posts

Hey all,

since I bought my r34 way back in 2015 my car has always been running a rich.

It’s just an unopened 25det neo with the stock op6 turbo running just above 12psi , with a blitz front mount, turbo back exhaust with cat, apexi intake, oil cooler and a power fc tune.

the thing is the car runs without problems, but when you start revving it past 4500rpm hard and pretty much 12psi or close, it blows a lot of black smoke . So much so that I get soot everywhere on the back of my car and my bumper just above the exhaust is permanently stained .

I know running rich means it’s using more fuel then needed but is there more to it? I regularly service my car and change spark plugs every service too (bcpr6es -8). 

There isn’t anything wrong with how the car runs. It actually runs perfect. No idle issues, no boost cuts, no pinging, no stuttering when climbing revs etc

Is there anything I can do to reduce the black smoke? Or is it just the way it is?

15 minutes ago, KiwiRS4T said:

What do your plugs look like when you change them?  Do you have a dyno chart of the afrs? Have you done a compression test?

The tips are always white, and the thread on the spark plug is black going down about 10mm. Don’t have the dyno sheet or compression test sheet. Never did it since I bought it. Also, the engine is at 246,000km

Reading plugs doesn't count for much unless you put fresh plugs in, do a wot pull and shut it down straight away.

I would put money on the tune is too rich in the boosted areas and lean/ok in the cruise areas

 

Get it tuned

14 minutes ago, Ben C34 said:

Reading plugs doesn't count for much unless you put fresh plugs in, do a wot pull and shut it down straight away.

I would put money on the tune is too rich in the boosted areas and lean/ok in the cruise areas

 

Get it tuned

No point now. I’m gonna go max hp without unopened motor, for rb25 it’s about 450hp right?  New turbo with supporting mods such as fuel pump and reg, ffp, z32 afm injectors etc then I’ll even sack the power fc (because it has fuel cut) get it tuned with either a nistune or ems 6860 so I can get 2 step and anti lag.

15 minutes ago, IM-32-FK said:

reg, ffp, z32 afm

All of this is wrong.

 

16 minutes ago, IM-32-FK said:

sack the power fc

This is OK, but unnecessary, because

 

16 minutes ago, IM-32-FK said:

because it has fuel cut

This is wrong

16 minutes ago, IM-32-FK said:

2 step and anti lag

Do you hate your driveline?

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...