Jump to content
SAU Community

Strongest sequential and why?

khezz
 Share

Recommended Posts

khezz Rising Star

khezz

Posted
Posted

With RBs pushing power further and further past 1000hp the demand on a gearbox is ever greater. 10 years ago a 1000hp transmission would be considered unbreakable. Now, with the cost of power parts going down and quality going up, the same person who could afford a sequential 10 years ago would be aiming for a number far higher then 1000hp. Keeping the cost aside and keeping dedicated drag boxes out of it (would love to see a thread on Liberty and Jericho transmissions)

Are transmission manufacturers keeping up?

What is the strongest sequential out there?

Why do you think/know so?

I am leaning towards the Hollinger. Been around for a very long time, very widely used in motorsports. Seems to be the only one with straight cut gears which eliminates sideload.

Link to comment
https://www.sau.com.au/forums/topic/481213-strongest-sequential-and-why/
Share on other sites
Old man 32 GTR Proficient

Old man 32 GTR

Posted
Posted

The Holinger sequential for GTR uses helical cut gears, as does PPG and OS 88. Samsonas and Albins use straight cut 

I think most would agree Albins would be top of the food chain 

Predator1 Rising Star

Predator1

Posted
Posted

You're right, back in the day, most of the GTR's though were either 2.6, or 2.8 only. RB30's werent THAT common.

I was in this exact boat when planning for a gearbox. I went with a 3.2 route. I sussed out all my options and talked to a tonne of people around what options there were for GTR's(excluding auto's here):

* Getrag 6 speed
* Gearset
* Sequential

Personally, I wanted peace of mind hence why I didnt go for a gearset or 6 speed. I mean, by the time you've done either of those 2 options you wouldn't get much change from 15K right? Plus, I dont know how long they would last with the fat torque of the 3.2...I also scoped out the sequentials out there, and in the end I went with the Albins as to me it seemed like the pick of the crop(Not saying the other Seq manufactures are shit, but its just my opinion). Plus, the Albins kit literally comes with everything minus the clutch.. no faffing around looking for tailshafts/transfer cases etc.

 

hattori hanzo Community Regular

hattori hanzo

Posted
Posted

I have a Holinger and love it, I bought it a few years about now circa 2015

 

however Albins and Samsona's seem to be the pick of the bunch these days.

 

Particularly now the albins can slot straight in without panel beating and the adjuster gear to tweak ratio's is very convenient and samsonas seems to put up with the beatings

BK Grand Master

BK

Posted
Posted
23 hours ago, Old man 32 GTR said:

Holinger sequential for GTR uses helical cut gears

I was under the impression you could get either, as the Holinger GRA-6N box for the group A R32 cars were straight cut, and was essentially the same ?

Anyway I would echo above - Albins all the way. Compared to Samsonas they have definitely more all round Motorsport proven track record within Australia and are completely Australian. In off road like 800hp+ buggies with monster torque that race here in the NT Finke desert race, there is basically only one manual box used that wins.

Albins

Old man 32 GTR Proficient

Old man 32 GTR

Posted
Posted

I called them not that long ago to ask a few questions about their sequential, they never mentioned anything about the option for straight cut? But I didn’t ask either, but the standard sequential design is helical cut. 

BK Grand Master

BK

Posted
Posted

Standard option looks like it, as the pictures in Holinger GTR workshop manual are all showing helical gears on the disassembly except reverse. Main and counter shafts are both splined on gear so they definitely can do it. The earlier GTR boxes the Hollinger GRA-6N and HKS-GTR were only straight cut.

2012 GTR MANUAL.pdf

IMACUL8 Veteran

IMACUL8

Posted
Posted (edited)

Same experience as Moray - when I spoke to Holinger couple months ago - helical only.  Not sure why that is now - as I'm sure you could get them in straight cut years ago.

I went with the new Albins ST6-LP - i believe its the only one with a internal oil pump.!

 

14 hours ago, Old man 32 GTR said:

I called them not that long ago to ask a few questions about their sequential, they never mentioned anything about the option for straight cut? But I didn’t ask either, but the standard sequential design is helical cut. 

 

Edited by IMACUL8

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      Blue slip

      By PranK · Posted

    • GTSBoy
      Ethanol Content Sensor - Always at 11%?

      By GTSBoy · Posted

      But seriously, can we ask for the results of the "tip a bottle of metho into a nearly empty tank" experiment?
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Dose Pipe Sutututu
      Blue slip

      By Dose Pipe Sutututu · Posted

      Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Stringycheese
      Blue slip

      By Stringycheese · Posted

      Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
×
×
  • Create New...