Jump to content
SAU Community

Recommended Posts

Hello everyone! I just got back from Iraq I spent 2 years there. I was deployed with as a soldier and after that I started working as a private contractor. Long story short due to the troop withdrawal I was able to come home and pick up this R32 GTR from RHDSpecialty. It is a 1994 R32 GTR in crystal white with a Nismo 320km/h cluster, Nismo gauge and a Kakimoto exhaust (I recently swapped to a Tomei Expreme Ti). I have been wanting a project car for the longest time but never had the funds and now after working 12 hours 7 days a week for 1 year in Iraq I was able to buy this legendary machine. I plan to clean up the engine bay and take care of the small rust that normally will come with this 26 year old car. Any inputs on body work and rust prevention will be greatly appreciated it!

1.jpg

2.jpg

3.jpg

4.jpg

  • Like 3

Welcome, 

That's a massive effort staying in Iraq for that long (I spent an 8months in Afghanistan years ago ) 

Looks pretty good at the moment. I don't have any experience with R32 bodywork but new suspension bushes and ball joints does make them a lot nicer to drive. 

26 minutes ago, PranK said:

Not much better than a white R32 GTR. Well done.

I'm envious at how much space you have to work on the car!

:welcome:

 

Yeah, the space belongs to my dad. He has a retirement home on 45 acres of land and this warehouse to myself. I get to bond with the car and bond with my dad lol.

31 minutes ago, robbo_rb180 said:

Welcome, 

That's a massive effort staying in Iraq for that long (I spent an 8months in Afghanistan years ago ) 

Looks pretty good at the moment. I don't have any experience with R32 bodywork but new suspension bushes and ball joints does make them a lot nicer to drive. 

I'll definitely keep note on that!

That's really tidy. Nice work. Treat it well and don't butcher it.

It looks like someone may have already done some work on the front suspension towers. That grey seam sealer around the tops is not original. Not saying it's a problem, just pointing it out.

 

  • Like 1

Chassis rails / sills, strut towers (as @GTSBoy  has pointed out), spare wheel well and passenger foot well (heater core) are the areas that I am aware of.

But there can be others depending on how far north the car spent most of its life.

  • Like 1
18 hours ago, GTSBoy said:

That's really tidy. Nice work. Treat it well and don't butcher it.

It looks like someone may have already done some work on the front suspension towers. That grey seam sealer around the tops is not original. Not saying it's a problem, just pointing it out.

 

I was curious about the sealer also. all of the R32 I was looking at in the market did not have this so I'm curious also to see what was done when it all comes out.

Started to remove more things off the car. I spent a lot of time labeling all the connectors from the harness. No way in hell I was going to remember where every single connector plugs into. My dad also gave me this massive LED light for the warehouse. The warehouse that came with the retirement home he bought had poor lighting or did not work. Shines super bright and I was able to conduct work at night instead of racing until the sun came down. 

5.jpeg

6.jpeg

  • 2 months later...

Life got in the way and I was finally able to come back to the R32. Man this is my first time ever fooling around with an engine removal and I'm breaking my engine removal virginity with an RB26 and holy f*ck this has been a pain in the ass! There is almost no room to do anything once you get to the plenum. Don't get me started with the top two tranny bolts. I was struggling horribly when it came to disconnecting the trans from the engine. After doing a little more research I realized this had a pull type clutch which required the throw out bearing to be released. So instead of releasing the throw out bearing I just released the fork instead.

130852243_1860101984165982_7743502363854409434_n.png

Engine 1.jpg

Engine 2.jpg

Engine 3.jpg

Engine 4.jpg

Engine.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...