Jump to content
SAU Community

Recommended Posts

hello! does anyone have the correct torque specs for the filler and drain plugs for:

  1. transmission: 
  2. front diff:
  3. rear diff:
  4. transfer case:

I have the service manual, but it only covers the engine, not the rest. I'm looking for specs on an r33 gtr, if it makes a difference.

thanks in advance, you absolute legends!

Well I happen to have those written down on a sticky note in front of me, but they are for R32 so use at your own risk.

1. Gearbox: Drain 18-25 / Filler 18-25

2. Front Diff.: Drain 18-25 / Filler 18-25

3. Rear Diff.: Drain 43-72 / Filler 43-72

4. Transfer Case: Drain 18-25 / Filler 7-14

All units are in lbs/ft., convert at your own risk.

  • Thanks 1

Transmission:

2071743657_ScreenShot2021-09-08at1_24_07PM.thumb.png.a047d12ef03d9c38802f2a13735549b0.png

Transfer case:

1305450273_ScreenShot2021-09-08at1_25_56PM.thumb.png.b94ede3ef6a58a2b8d4df44571f6d5cf.png

Front and Rear differential:

451709289_ScreenShot2021-09-08at1_36_16PM.thumb.png.c635dbd193abbc862dc71ff6a74be527.png

 

All taken from the R34 workshop manual, I'm pretty sure that the differentials and therefore the torque specs are the same. The R34 GTR transmission is different but they list a torque spec for the 30A transmission which is shared with the R33 GTR. Transfer case is a different part on the R34 GTR with a thinner chain. It would be nice to get the Japanese R33 workshop manual, the english manuals out there tend to not be as comprehensive and between DeepL/Google Translate you don't really need a fully translated manual these days.

  • Thanks 1

Don't be afraid to use the lower end of that range for those tapered plugs. They have an amazing ability to self tighten over time and I have never seen one of them leak from being undertightened.

  • Like 1
  • Thanks 1
On 9/8/2021 at 1:48 PM, Duncan said:

Don't be afraid to use the lower end of that range for those tapered plugs. They have an amazing ability to self tighten over time and I have never seen one of them leak from being undertightened.

A guy I know near me recently rounded off his front diff plugs so definitely don't go nuts, especially with the fill plug. Spark plugs are about the only thing where I try to tighten to middle of torque spec instead of lower end of torque spec and I do it with the engine cold. 

On 9/8/2021 at 4:03 PM, TXSquirrel said:

Well I happen to have those written down on a sticky note in front of me, but they are for R32 so use at your own risk.

1. Gearbox: Drain 18-25 / Filler 18-25

2. Front Diff.: Drain 18-25 / Filler 18-25

3. Rear Diff.: Drain 43-72 / Filler 43-72

4. Transfer Case: Drain 18-25 / Filler 7-14

All units are in lbs/ft., convert at your own risk.

@TXSquirrel buddy, this is exactly what i needed. thanks!!!

On 9/8/2021 at 4:44 PM, joshuaho96 said:

Transmission:

2071743657_ScreenShot2021-09-08at1_24_07PM.thumb.png.a047d12ef03d9c38802f2a13735549b0.png

Transfer case:

1305450273_ScreenShot2021-09-08at1_25_56PM.thumb.png.b94ede3ef6a58a2b8d4df44571f6d5cf.png

Front and Rear differential:

451709289_ScreenShot2021-09-08at1_36_16PM.thumb.png.c635dbd193abbc862dc71ff6a74be527.png

 

All taken from the R34 workshop manual, I'm pretty sure that the differentials and therefore the torque specs are the same. The R34 GTR transmission is different but they list a torque spec for the 30A transmission which is shared with the R33 GTR. Transfer case is a different part on the R34 GTR with a thinner chain. It would be nice to get the Japanese R33 workshop manual, the english manuals out there tend to not be as comprehensive and between DeepL/Google Translate you don't really need a fully translated manual these days.

@joshuaho96 i found a manual that they sell out of NZ, that is supposed to have everything (engine, chassis, and some other stuff) and it sells for a decent price, but i don't know anyone that has purchased it. what i don't want to do is pay for the engine only file that everyone has been sharing.

On 9/8/2021 at 4:48 PM, Duncan said:

Don't be afraid to use the lower end of that range for those tapered plugs. They have an amazing ability to self tighten over time and I have never seen one of them leak from being undertightened.

@Duncan always chiming in with the excellent advice!

 

thanks all of you!

On 9/8/2021 at 3:14 PM, itsforandres said:

@TXSquirrel buddy, this is exactly what i needed. thanks!!!

@joshuaho96 i found a manual that they sell out of NZ, that is supposed to have everything (engine, chassis, and some other stuff) and it sells for a decent price, but i don't know anyone that has purchased it. what i don't want to do is pay for the engine only file that everyone has been sharing.

@Duncan always chiming in with the excellent advice!

 

thanks all of you!

They mention that the engine manual is a crappy scan of their old translation uploaded to the internet. The 150 dollar manual is the complete workshop manual supposedly. I might spring for that down the road, it gets tiring to cross-reference against the R34 manual. The suspension components especially are different so I'm not sure what the torque specs would be there.

  • Like 1

As far as I know, the only JPNZ R33 manual is about 500 pages and engine only. Given that JPNZ went to the effort of scanning, translating and collating all those pages, I'd encourage anyone who needs it to pay the small amount for the trouble it can save you.

I have not seen a scanned full copy of an original japanese R33 manual, although I do have the W34 Stagea one.

On 9/8/2021 at 3:22 PM, Duncan said:

As far as I know, the only JPNZ R33 manual is about 500 pages and engine only. Given that JPNZ went to the effort of scanning, translating and collating all those pages, I'd encourage anyone who needs it to pay the small amount for the trouble it can save you.

I have not seen a scanned full copy of an original japanese R33 manual, although I do have the W34 Stagea one.

"Below is the index from the manual it is a copy and paste and not laid out as it should be but is the full index. Please note this is a full factory workshop manual not just the engine but a manual for the entire vehicle. Some idiot did copy our engine manual for this vehicle and sells it online and it is a shit scan and only covers the engine, since then we translated the rest of the Japanese manual which covers the entire vehicle. We get asked all the time if this is just the engine or the full manual. This is the full manual."

On 09/09/2021 at 8:08 AM, Duncan said:

Good on them....massive job.....buy, buy, buy and give them a small payback for the huge effort they have put in.

I have the R33 chassis manual - it is excellent. Waited ages for them to finally do it, as I was annoying them all the time for full version in 2004 after buying their engine manual.

I find it much much faster to have the hard copy out. Speaking of, this is very very temping when back in stock:

https://www.automotobookshop.com.au/nissan-gtr-r32-service-workshop-manual-2-volume-set/

  • Like 1
On 9/8/2021 at 6:38 PM, Duncan said:

Good on them....massive job.....buy, buy, buy and give them a small payback for the huge effort they have put in.

i did! i ordered right after i made the post!

 

On 9/8/2021 at 6:33 PM, joshuaho96 said:

"Below is the index from the manual it is a copy and paste and not laid out as it should be but is the full index. Please note this is a full factory workshop manual not just the engine but a manual for the entire vehicle. Some idiot did copy our engine manual for this vehicle and sells it online and it is a shit scan and only covers the engine, since then we translated the rest of the Japanese manual which covers the entire vehicle. We get asked all the time if this is just the engine or the full manual. This is the full manual."

i didn’t see that on the page. i just took a chance and ordered it!

On 9/8/2021 at 7:13 PM, BK said:

I have the R33 chassis manual - it is excellent. Waited ages for them to finally do it, as I was annoying them all the time for full version in 2004 after buying their engine manual.

I find it much much faster to have the hard copy out. Speaking of, this is very very temping when back in stock:

https://www.automotobookshop.com.au/nissan-gtr-r32-service-workshop-manual-2-volume-set/

i’d never seen that site nor that book! will bookmark, thanks!

On 09/09/2021 at 8:47 AM, itsforandres said:

i’d never seen that site nor that book! will bookmark, thanks!

It's the official Nisssn Australia 32 GTR manual. I know it's the one everyone has a scanned copy of including myself, but the fact it is still obtainable is tempting.

I reckon the scan of the 32 manual originates with me. I sneakily borrowed a copy from Nissan back in about 1999 or so. I made 3 photocopies (because scanning it at that point in time was actually a bit too much of a challenge) and distributed 2 copies to others who knew I had borrowed the original.

Although, the Nissan original was in a lever arch folder, not a bound book, so was probably a workshop copy anyway.

The PDFs that are around all contain some artefacts from my photocopies that were not on the original paper I copied. So I reckon one of the other copies got scanned early in the 2000s and ran away to the internet.

well, you have done the world a great service then!

I actually have the original hard copy too picked up a copy I saw a few years back like a seagull on a hot chip, I only really use it for tracing wiring as the scan it not really legible for a lot of the detail

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...