Jump to content
SAU Community

Recommended Posts

Hey Guys

I have a 1994 R32 GTR which I have owned for years. It's always been silky smooth yet the other day I started it and the car felt weird. 

Stationary at low RPMs between 1000-2000 the car vibrates. You can feel it through the seat but mostly the steering wheel. No knock, no smell, no issues driving just this weird vibration. Above 2000 you don't feel it anymore. Not sure if it goes away or can't be felt due to higher revs. Car just finished a 400KM drive a few weeks back without any issues. 

I have seen this problem on many forums including SAU and nobody ever posts whether it gets fixed. Hoping this time someone can give me feedback or has fixed it so we can update the forum with a fix.

 

 

How is the idle? Are all injectors flowing properly? I recommend running a cylinder balance test where you disable injection on each cylinder at low idle and see if any one of them seems to have a weak influence on idle RPM, they should all drop the same amount of RPM when you turn it off.

On 2/6/2022 at 7:42 AM, White GTS-T said:

You've owned it for years, have you ever replaced the engine mounts? I'd be checking and testing all the engine mounts first, including the gearbox mount.

No I haven't. I was thinking this could the case but wouldn't there be rock in the engine when starting?

On 2/6/2022 at 7:36 AM, joshuaho96 said:

How is the idle? Are all injectors flowing properly? I recommend running a cylinder balance test where you disable injection on each cylinder at low idle and see if any one of them seems to have a weak influence on idle RPM, they should all drop the same amount of RPM when you turn it off.

Idle is perfect. No hunting, very smooth. I haven't done the cylinder balance test yet why would it only do it at low RPM?

Yes, if the engine is vibrating but running smoothly it is probably not a missfire.

I'd check all of the accessory belts carefully, and make sure all of the accessories are mounted properly, eg power steering pump is tight. There are lots of other rotating bits that could come out of balance (eg, the harmonic balancer itself) but at least you can check those easily. If you have a timing light, check the base timing against the balancer too, if it is miles off it may be the balancer

  • Like 1
On 2/7/2022 at 1:22 PM, WantGTR said:

if it does end up being a balancer, hopefully you havent damaged the keyway on the crank. best to get a new keyway as well.

So the balancer can damage the keyway immediately or does it take a while. Problem hasn't been an issue for long 

On 07/02/2022 at 7:48 PM, dtorreal said:

So the balancer can damage the keyway immediately or does it take a while. Problem hasn't been an issue for long 

Depends how bad the vibration is guess. if the balancer bolt backs out or the balancer is bouncing around it can do damage yes.

Last year this happened to me...

20210930_155935.thumb.jpg.c983ad876306294d557ac2e1104e238c.jpg

If balancer has become faulty and loosened after being tightened to 460nm + there is sometimes another cause. The most overlooked part that makes them come loose is not the bolt or balancer itself, it's the rubbish lower factory timing gear and shields. They seem to crush after extended use or under high loads.

Ross have an excellent billet full replacement for this which I have now used.

20211228_144357.thumb.jpg.296c8aa13c0434f66889fa607a77beb9.jpg

If the balancer needs to come off I strongly suggest inspecting the lower timing gear area. Dead give away for being crushed is when the back of the balancer is touching or almost touching the lower timing cover.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power steering is probably because someone has nuked the HICAS CU and you no longer have the variable power asist doing what it is supposed to. How much boost are you running? You are aware that any more than 10 psi on the stock ECU is just asking for it to go to full R&R (that's Rich & Retard, which is effectively Retarded and Retarded!) which kills all the power. Depending on the exact conditions, it can just be runnign on the fat and stupid end of the maps, then the conditions change, you make a little more boost and the ECU goes into panic.
    • @BuiltNotBought Just as GTSboy said.   If you want driveabilty and more low down torque..keep the stock runners. They are VERY good from a factory. I have them too on my RB25DET NEO and as a GTSboy i have fmic but with stock piping route(i have Blitz intercooler) Iam making around 320 BHP and the car pulls "hard" from like 2,5k all the way to 7k. I have it dyno tuned to mimic N/A power curve and making little less max torque due to the smallbox tranny. But driveability is very great. I had 350Nm below 3k so car feels very quick.   EDIT:  Not my channel but i saw this and i know that is what i want (and i have exactly this)  
    • Looking to sort out a couple of issues on my skyline  It recently was rebuilt, however rebuilder long story short did not give two flying effs about the work he did. So moving forward it's running but I have two persistent issues 1) it has a misfire / lag type of issue (was at higher RPMs but I had a dead piggy back ecu removed which improved it) now it's not as bad but still does it at random, I thought it may have been a boost issue I'm running an older turbosmart dual stage controller, turbosmart told me to try running off gate pressure however it still has a lag at random times. It has New MAF, maf plug, coil packs, sparks, CP harness.. injectors tested and cleaned. Factory ECU. 2) Power steering issue. It is tight as anything. Flushed power steering, rebuilt my pump because the bearing was shot. Flushed again still tight (mainly when parking and going slow into my driveway etc)  No kinks in hard lines, replaced the lines I could see had cracks. Still tough to steer.  I was told to shim a coin and place into the solenoid plug? Is there anything else. My steering angle sensor also has a issue. It's a used one I replaced, does it need to be calibrated? I feel like I've tried everything and this car is my voodoo doll.   
    • Holy shit... wow!!! I totally missed this
    • One main filter. Each tank has a prefilter to keep rocks and small children out, then the big main filter that also does water separation. Clogged the first one so bad it was like a rev limiter at 3200rpm. Literally just like dropping the throttle off and maintaining rpm!
×
×
  • Create New...