Jump to content
SAU Community

C34 25det neo

Jarrod rb25det
 Share

Recommended Posts

Jarrod rb25det Newbie

Jarrod rb25det

Posted
Posted (edited)

Hey I've got a s2 c34 with rb25det neo after I installed a highflowed 25det turbo the car hesitates for a second between gears when coming off boost then back on throttle. I was running a frontmount no problems with the stock turbo and I've jst installed the sidemount and now it's fine again with the frontmount and highflowed turbo is the afm not coping with the extra air flow or what I'm stummped

Edited by Jarrod rb25det
Link to comment
https://www.sau.com.au/forums/topic/483484-c34-25det-neo/
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

Any larger turbo worth using will flow more at at "low boost" than the stock turbo does wound all the way up to "turbine flies off". You can't really go past the airflow available from the stock turbo at 10 psi without the stock ECU starting to get upset, and at 11-12 psi it will really be pissed off. I wouldn't contemplate a highflow on a stock ECU without Nistuning it to get around all that.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/483484-c34-25det-neo/#findComment-7962435
Share on other sites
BK Grand Master

BK

Posted
Posted
On 24/03/2022 at 12:24 PM, Jarrod rb25det said:

Like I said I have a link g4x but havnt been able to tune it that's not my question anyway I'm jst cruising until it gets tuned but with the frontmount it buzzes out and the sidemount it doesn't that's my question 

I think you've just demonstrated how shit your side mount intercooler actually is in pressure drop and flow across its core compared to your front mount.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/483484-c34-25det-neo/#findComment-7962446
Share on other sites
robbo_rb180 Grand Master

robbo_rb180

Posted
Posted

go back to the front mount, install the Link and road tune the low load stuff, plenty of people can help like myself or @Dose Pipe Sutututu
Depends where you live an experienced member may be able to help with the install & setup

 

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/483484-c34-25det-neo/#findComment-7962453
Share on other sites
robbo_rb180 Grand Master

robbo_rb180

Posted
Posted
On 3/25/2022 at 4:54 PM, Jarrod rb25det said:

I've now installed the link g4x calibrated everything set base timing and finally got it running afrs are rich on idle but fine cruising but ran out of daylight so will have to tidy things up tomorrow 

 

Good work
Easy to trim fuel, build a Lambda/afr target map and can use the quick tune function to get it pretty good quickly but need to turn off any other trim tables.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/483484-c34-25det-neo/#findComment-7962515
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...