Jump to content
SAU Community

Recommended Posts

Before i buy injectors and fuel pump etc and leave the car for tuning, which size of injectors would you go for? 

I think i want to run as low power as i can with the GT28-5 turbos. But would be nice to have some room for more maybe. 
I have OEM injectors refurbished and cleaned but they wont probably be enough as someone mentioned here before?
 

Fuelpump about 255l/h - 340l/h?

something else you would change before tuning the car?

Setup:

Rb26dett with

-twin GT28-5 turbo

-JE-pistons 8.2:1

-Eagle H-Beam rods

-ACL race main and rod bearings

-Oil pump collar installed

-Older verision of LINK G4 ECU

 

 

Link to comment
https://www.sau.com.au/forums/topic/484357-rb26-setup-power-and-injectors-size/
Share on other sites

  On 12/01/2023 at 10:25 PM, Dose Pipe Sutututu said:

Why are you choosing to go with such low compression?

Expand  

I actually dont know. These was ordered from Realstreetperformance, and i belive i had these recommended by them but i could be wrong. Could be the the guy building the engine that told me to get these ones as well. 

  On 12/01/2023 at 6:32 AM, djr81 said:

Assume you have the ballast delete and a new AIT sensor? Plus someone who can tune TPS?

Expand  

Thank you for the reminder about the ballast delete. 

AIT? Do you mean intake air temperature sensor? 

Well, i guess the tuner can tune the TPS 😬

  On 11/01/2023 at 8:04 PM, GTSBoy said:

Just go straight for 1000cc Bosch ID14s from somewhere reputable. A ~340L/h TI pump would be fine. Wired properly, of course.

Expand  

Okey, thank you. How lower power could i run with the 1000cc:s do you think? How much power can the engine handle? I do not want to push anything. :)

I will re-wire the fuelpump! Thanks for the reminder. 

  On 13/01/2023 at 6:24 PM, reallyspeedly said:

How lower power could i run with the 1000cc:s do you think?

Expand  

Stock. If it will idle on an injector (and of course, with a decent computer, the engine will idle on 1000s) then it can run ANY power level above that (up to the limit of the injector capacity, of course).

  On 13/01/2023 at 6:24 PM, reallyspeedly said:

How much power can the engine handle? I do not want to push anything.

Expand  

Most of your list of engine mods would contribute to being able to run up to the limit of what the turbos can provide - except for one thing. I would not attempt to do so without a significant oil pump upgrade, and then paying attention to the engine breathing and oil draining situation - as per the oil control thread (or the last 100-150 pages of it anyway).

  • Like 1
  On 13/01/2023 at 6:19 PM, reallyspeedly said:

I actually dont know. These was ordered from Realstreetperformance, and i belive i had these recommended by them but i could be wrong. Could be the the guy building the engine that told me to get these ones as well. 

Expand  

Send them back and get a higher cr.

  On 13/01/2023 at 6:22 PM, reallyspeedly said:

Thank you for the reminder about the ballast delete. 

AIT? Do you mean intake air temperature sensor? 

Well, i guess the tuner can tune the TPS 😬

Expand  

Yes for the air inlet temp and not what I meant for the tune. See here. Some tunas talk a good game but individual throttle body tunes are beyond them. Where abouts in the world are you?

 

 

  • Like 1
  On 13/01/2023 at 10:51 PM, GTSBoy said:

I would prefer being able to stop for fuel anywhere I like rather than the fuel stations with E85 being 15-20km apart.

Expand  

Hence full flex allows just that, depending on fuel choice your power will vary.

When you feel like a 20 year old fuccboiiii and want to race people on the street or actually go to a race track then fill it up with E85 then top up the tank with 98RON for your commute with whatever ethanol is left.

  On 14/01/2023 at 2:53 AM, Dose Pipe Sutututu said:

Hence full flex allows just that, depending on fuel choice your power will vary.

When you feel like a 20 year old fuccboiiii and want to race people on the street or actually go to a race track then fill it up with E85 then top up the tank with 98RON for your commute with whatever ethanol is left.

Expand  

Exactly what I do having the cars on flex, and I live somewhere where E85 has to be drummed up.

  On 13/01/2023 at 11:29 PM, djr81 said:

Yes for the air inlet temp and not what I meant for the tune. See here. Some tunas talk a good game but individual throttle body tunes are beyond them.

Expand  

True that so many tuners want to try to tune individual throttle RB26s with MAP because they don't understand TPS fuel load and then get poor results.

One of the many reasons I went to Simon at Morpowa as one of the few who I had confidence in to do it on fuel TPS load with the Haltech.

  • Like 1
  On 14/01/2023 at 10:08 AM, reallyspeedly said:

Is there any good reason for this? It's too late to send them back, the engine is built awhile ago already.

Expand  

Well if the motor is built then it's built. 

There are many good reasons for higher compression ratio though, more power at all rpm, increased turbo spool, better off boost performance, more low end torque.... I could keep thinking of ways to say "the engine will perform better, everywhere" but you get the idea. 

  • Like 1
  On 14/01/2023 at 10:53 AM, Murray_Calavera said:

Well if the motor is built then it's built. 

There are many good reasons for higher compression ratio though, more power at all rpm, increased turbo spool, better off boost performance, more low end torque.... I could keep thinking of ways to say "the engine will perform better, everywhere" but you get the idea. 

Expand  

Yeah, i was sitting here and realise that. Well this car got really shitty.. wrong turbo setup, wrong pistons, ecu, etc etc..

 

i guess i have to ask the engine builder about this, cause for some reason he installed them and this guy is really good with what he's doing. 
 

Edited by reallyspeedly

Turbos are fine, just a bit old school as the hipsters have diluted their gtr purity and gone for singles. They are still good units, however and the blokes with ponytails and beige Volvo dailies can get stuffed.

‘The ecu is a good ecu. You just need a good tuna to tune it. My point wasn’t to put down the setup just to highlight you need someone familiar with rb’s and their idiosyncrasies.

.3:1 isn’t earth shattering on the cr. Certainly nothing E85 won’t compensate for in spades if you go that way.

So yeah don’t get negative about it. It will work fine and be loads of fun. FWIW I’ve got -5 turbos and a Link ecu.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've got a spare standard box sitting in the garage  I know it will come one day though, but it's driven pretty tamely on the four times a year it gets out... 
    • Big question… have you decided on a gearbox? Because it’s going to come… and a gearset ain’t going to do the job.    save your pennies 🤪
    • it was good to see our presence at GTR festival..hope to see more SAU at these events 
    • This is awesome.     
    • Thanks for the quick replies guys its appreciated. A small extension was welded onto the standard 6boost external gate pipe which you can see where the pipe goes from black to stainless just below and to the right of the rear housing in the first picture. Overall I would say the flow is pretty good other than 6boosts choice to come straight off the collector at a decent angle.. Not sure why I went with two valves, I originally replaced the stock twin bovs with the GFB when I had the twins on. When I purchased the EFR it came with the Turbosmart Kompact BOV so I figured that would be a better option than the stock EFR Bov. I don't believe the Turbosmart BOV is adjustable? When I get the spike and then sudden dip in boost pressure, the turbo speed does drop as well. Stock head size wise however I believe it has Neo Turbo springs and a Neo Turbo intake camshaft and an aftermarket exhaust camshaft in the vicinity of 260 degrees. We didn't try a different MAC valve, we tried two different ways of plumbing it and we also tried removing the mac valve entirely and just having the boost source from the turbo directly connected to the wastegate and it still spiked / dropped and exhibited the same behaviour. Standard R33 GTR 5 speed tansmission. I'm running a Haltech Elite 2500 and can provide some logs if you. I understand what you're saying in that it looks like an auto plot however no, it's still a manual and it just has a lot of torque down low, for all intents and purposes it's a very impressive street car. I've attached a photo of the quickbitz dyno plot which was when the only difference is I was running -5 twin turbos with a mac valve. As you can see theres a decent dip in AFRs between 125kmh and 135kmh. Our problem now is not that the AFRs are dropping, just the boost pressure is dropping, however it is evident in the same RPM range of the map, coincidentally or not.
×
×
  • Create New...