Jump to content
SAU Community

Recommended Posts

Good afternoon,

I've got a leak out of one of the half-shafts and need to replace the seal.

I've searched for a guide/another thread, nut can't seem to find one (happy to be corrected)

What is the method for removing/reinstalling the half shaft after replacing the seal.

 

Cheers

received_918381569340257.jpeg

Link to comment
https://www.sau.com.au/forums/topic/484428-removing-half-shaft-from-diff-r33/
Share on other sites

  On 09/02/2023 at 5:21 AM, Pattey21 said:

Good afternoon,

I've got a leak out of one of the half-shafts and need to replace the seal.

I've searched for a guide/another thread, nut can't seem to find one (happy to be corrected)

What is the method for removing/reinstalling the half shaft after replacing the seal.

 

Cheers

received_918381569340257.jpeg

Expand  

When I had to do this for the front diff I removed the diff cover and spun the diff until I could see the axle inside the diff. Then I used a plastic pry tool with a simple flat edge that gradually widens to full width and a hammer. Jam the pry tool in and use a hammer until the axle pops out. As far as I can tell it did not mar or bend any other parts of the diff this way. My least favorite thing is scraping/prying something out with metal on metal so this was a foolproof technique for me and the car needed a diff oil change pretty badly anyways. Then I used a slide hammer with an expanding jaw puller to remove the seal itself. Be careful when you do this because it will suck to damage the seat of the seal. I expanded it into the rubber to keep it from marring the seat instead of trying to catch the back edge where it meets the seat.

Another method I've seen since doing that job was a tool that hooks onto the outside of the axle and makes it possible to slide hammer the axle out instead of trying to use a pry bar.

  On 09/02/2023 at 7:20 AM, joshuaho96 said:

Another method I've seen since doing that job was a tool that hooks onto the outside of the axle and makes it possible to slide hammer the axle out instead of trying to use a pry bar.

Expand  

Yuh, a bit of flat bar with 3 holes in it.

  • 3 weeks later...
  • 2 weeks later...

So i refilled it and layed it on its side for a day (new seal side down) no leak, went for a drive today and its weeping. Is it possible to be weeping from the half shaft seal, do the take time to bed in?

The seal cam pre-greased in the centre and i lubricated the shaft prior to install.

  On 15/03/2023 at 8:15 PM, Pattey21 said:

I didn't inspect it thoroughly but my impression when cleaning it prior to lubrication, was the it was "serviceable" but my focus was more on the seal itself.

Expand  

Not 100% across this half shaft in particular as I haven't removed one, but it will be pretty much the same as others...

 

The surface the seal rests on on the half shaft itself can also wear. If it starts to wear down, it's not going to mate and seal properly. 

When doing the seal, you need to be checking the inner and outer surfaces it mates to, are in good condition too.

 

Is the oil weep 100% coming from the half shaft seal location?

Have you checked the breathers/vents aren't blocked?

Blocked vents will bust an axle seal/make them weep. This could be why it only showed after a drive, as it needed to heat up and pressurise first (diff unable to breath)

  • 2 weeks later...

Hectic few weeks at work.

I made sure to clear/check the diff vent but I will check the breather hose.

My guess for it being the half shaft seal location is based on filling it prior and lying it on the damaged side overnight and it did not weep.

ill have another look underneath/ check the breather hose

 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...