Jump to content
SAU Community

Recommended Posts

hey guys i know it’s probably a stupid question but i recently got a new turbo and just wanted to know how bad for my car it would be if i drive it with everything else stock in the car aside from a front mount intercooler i have a 1998 r34 gtt and i am putting a Kinugawa Turbo 3" Anti Surge TD06SL2-20G for Nissan Skyline 

just wondering and hoping someone would know how much more i’m gonna need to upgrade 

Edited by justin parker
Link to comment
https://www.sau.com.au/forums/topic/484785-turbo-swap/
Share on other sites

Hi mate, if it starts and drives I'd be surprised, and if you bring it onto boost you will probably kill the motor.

A larger turbo pushes more air (even at wastegate boost), but the factory ECU will only have limited ability to deal with that (say, within a couple of %). Once it goes outside what it expects, it adds heaps of fuel and removes heaps of timing to keep the engine safe from what it expects is a malfunction.

You'll need a tune and/or aftermarket ECU, larger injectors, either larger air flow meter or swap to MAP sensor, probably a boost control solenoid, all the usual. 

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/484785-turbo-swap/#findComment-7981029
Share on other sites

This is going to sound simplistic, but it is, and here I go

Everything on the car exists to support the turbo

So if you change that, the list of things you should _consider_ upgrading is approximately the entire vehicle.

  • Like 3
Link to comment
https://www.sau.com.au/forums/topic/484785-turbo-swap/#findComment-7981035
Share on other sites

Agree with the above.

To put it plainly - the stock turbo is good for ~200rwkW at just enough boost pressure to make it explode (<14 psi). Everything on the car that works with that - the fuel pump, the injectors, the AFM - all of these are only good to about that power level. Some a bit less, especially if old and tired. Some a bit more. But all about the same. The stock clutch will not tolerate even that much for long. The stock auto gearbag will raise the white flag at that power level too.

The TD06 you're putting on is good for upwards of 260 rwkW, at substantially more boost. But even at the same boost as the stocker, it will make a lot more power. As Duncan said, if you put your foot down and ramp up the boost, you will push past the capacity of the fuel system to keep up with the air flow, lean it out and pop it.

Unlike what Duncan said, I would expect it to start and drive. It is an AFM ECU, so it will measure the idle and cruising air flow and provide fuel for that just fine. And that's the danger. Because it should feel fine and it will want to go and when you do.....pop.

Link to comment
https://www.sau.com.au/forums/topic/484785-turbo-swap/#findComment-7981038
Share on other sites

11 hours ago, Murray_Calavera said:

What ECU are you going to use? 

Are you going to install all of the supporting mods yourself and then pay a workshop to tune it?

yeah i’ve talked to a shop and they told me the supporting mods i need then im leaving the ecu stuff to them. i have a automatic r34 so they said my stock ecu will control the transmission and the will wire in a haltech 

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/484785-turbo-swap/#findComment-7981068
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...