Jump to content
SAU Community

Recommended Posts

Hey all, on my Subaru I noticed I have a whistling sound when from 60km an hour onwards, below that I don't hear it. I used to hear it from 80km onwards but now it's 60km. It does seem to get louder then plateau's, I thought maybe it's the wheel bearings but I got them replaced about 70,000km ago, unless the mechanic put cheap ones on. What would you guys lean towards it being? Also when going over small bumps and especially when I'm turning the wheel on bumps I can hear like a twitching sound I think from the rear passenger side, maybe the strut? 

I know the rear of the car itself has been squeaky probably since I bought it (separate issue), but I've never fixed it as I generally don't have people sitting in the back and it's not overly noticeable unless I go over bumps with people in the back or if I'm driving myself but turn into a carpark ramp to go up the parking.

On 11/07/2023 at 10:35 PM, GTSBoy said:

You seriously want us to attempt to diagnose odd sounds over the internet?

To be fair something like every second engine issue thread starts with a recording of odd noises happening in the engine bay, no? In that sense I'd say having a recording would be good for a start.

44 minutes ago, soviet_merlin said:

To be fair something like every second engine issue thread starts with a recording of odd noises happening in the engine bay, no? In that sense I'd say having a recording would be good for a start.

Yeah, but when it's happening at 60+ km/h, good luck trying to get a recording that we can hear anything over the wind roar.

On 11/07/2023 at 9:34 PM, silviaz said:

I thought maybe it's the wheel bearings but I got them replaced about 70,000km ago,

Could still be wheel bearings. Or a diff? Dunno if that's a whistle, probably more a whir.

Sounds like the rear is unrelated? Hard to diagnose anything with the amount of info though. YOu could get under the back and just check everything is tight ?

5 hours ago, PranK said:

Could still be wheel bearings. Or a diff? Dunno if that's a whistle, probably more a whir.

Sounds like the rear is unrelated? Hard to diagnose anything with the amount of info though. YOu could get under the back and just check everything is tight ?

Bearings got replaced (could have been cheap ones, though I am leaning towards it), will get it checked out one of these days. Doubt it's the diff, can't hear it on passenger side only driver side.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...