Jump to content
SAU Community

Rb25 blown?

Prof_Finesser
 Share

Recommended Posts

Prof_Finesser Enthusiast

Prof_Finesser

Posted
Posted

Hello again I just got my rb25 tuned yesterday made 450 forged internals and semi built head I went on a beer run and let the car warm up before I got on it and I did a small pull and then about a minute later the engine shut off. I towed it back to the house and been tearing into it today. It’s odd I cant turn the engine by hand to the right (intake to exhaust side) it has some wiggle then it stops and won’t turn any more but I can turn it to the left no problem. I did a leak down and all cylinders were in good condition. I’m so lost at this point. I checked cams in case they snapped and they are all good too. I think I’m going to pull the head off tomorrow just to see what’s going on because I don’t understand.

Link to comment
https://www.sau.com.au/forums/topic/485778-rb25-blown/
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

Well, it's too weird to be making any guesses. I'd have the plugs out and a borescope into the cylinders before doing anything else.

When you say

51 minutes ago, Prof_Finesser said:

I can turn it to the left no problem

Do you mean to say that you can turn it over continuously? Like, it's not seized or blocked from rotation outright? Only won't turn forwards? If so, would sound perhaps like something has dropped into the timing belt area or has otherwise arranged itself like a ratchet pawl, so that it prevents rotation one way, but not the other.

Link to comment
https://www.sau.com.au/forums/topic/485778-rb25-blown/#findComment-7992553
Share on other sites
Prof_Finesser Enthusiast

Prof_Finesser

Posted
  • Author
Posted
3 minutes ago, GTSBoy said:

Well, it's too weird to be making any guesses. I'd have the plugs out and a borescope into the cylinders before doing anything else.

When you say

Do you mean to say that you can turn it over continuously? Like, it's not seized or blocked from rotation outright? Only won't turn forwards? If so, would sound perhaps like something has dropped into the timing belt area or has otherwise arranged itself like a ratchet pawl, so that it prevents rotation one way, but not the other.

Yes and that’s what I think as well and yes the rotation is continuous 

Link to comment
https://www.sau.com.au/forums/topic/485778-rb25-blown/#findComment-7992554
Share on other sites
Prof_Finesser Enthusiast

Prof_Finesser

Posted
  • Author
Posted
3 minutes ago, Dose Pipe Sutututu said:

Most likely won't hold pressure, however it is still possible if the valve isn't bent

I just realized something I’m at TDC and my intake cam is at the timing mark the horizontal mark and my exhaust cam is at like 7-8 o’clock position not even close to the timing mark. I’ve timed these engines about 5 times now and always do it the same line up the 3 marks crank and two cam. How tf have my cam spun that far off. I’m gonna check all the timing system tomorrow 

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/485778-rb25-blown/#findComment-7992567
Share on other sites
MBS206 Grand Master

MBS206

Posted
Posted
3 hours ago, Prof_Finesser said:

I just realized something I’m at TDC and my intake cam is at the timing mark the horizontal mark and my exhaust cam is at like 7-8 o’clock position not even close to the timing mark. I’ve timed these engines about 5 times now and always do it the same line up the 3 marks crank and two cam. How tf have my cam spun that far off. I’m gonna check all the timing system tomorrow 

Many possibilities, like cam gears coming free of the cam shaft and spinning.

Link to comment
https://www.sau.com.au/forums/topic/485778-rb25-blown/#findComment-7992575
Share on other sites
Prof_Finesser Enthusiast

Prof_Finesser

Posted
  • Author
Posted

So good news and bad head is off. Good news engine is turning again forwards continuously and pistons have very small mark on the top where valves hit it does catch a finger nail going to still ask machinist if it’s ok to run I think they will be ok.  On to the bad I took the exhaust cam off because the exhaust valves where the only on the pistons and it seems like my first cam cap (closest to timing gear) was eating into the camshaft and end up stopping it all the valves have the marks in picture. 
 

IMG_4302.jpeg

IMG_4303.jpeg

Link to comment
https://www.sau.com.au/forums/topic/485778-rb25-blown/#findComment-7992588
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Butters
      R34 GTR Speedo Drive , sensor type ?

      By Butters · Posted

      Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • Duncan
      spot the stagea

      By Duncan · Posted

      roof rail delete used to be a thing, they were made locally for a while too
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • AnimalGarage
      Can you mount the ATTESA pump in other locations?

      By AnimalGarage · Posted

      According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...