Jump to content
SAU Community

Recommended Posts

  • PranK changed the title to Disposing of shocks/struts?

I booked a council pick-up for a bunch of stuff and left them out the front, with all rubbish to be picked up, on the top with other bits of scrap metal, the arvo before pick up.

Inevitably the metal scrap guys turn up and take all the metal that arvo.

They must have a deal going cause they certainly know what addresses to show up at !

Works every time !

Edited by PLYNX
  • Like 1
58 minutes ago, PranK said:

It was the pressure I was worried about. @GTSBoy does drilling them pose any problems?

Nah. There's not shit tonnes of pressure in there. Just drill with a 1.5mm drill or something equally tiny. When the drill goes all the way through thee gas will start to come out, but with such tiny path through the flutes of the drill bit, it won't be at all dangerous. You can be as paranoid as you like from then on. I'd just pull the drill out while keeping my face out of the line of fire. But then, I spend half my time looking into pressurised furnaces. So my risk acceptance is somewhat higher than most!

  • Thanks 1
9 hours ago, GTSBoy said:

Nah. There's not shit tonnes of pressure in there. Just drill with a 1.5mm drill or something equally tiny. When the drill goes all the way through thee gas will start to come out, but with such tiny path through the flutes of the drill bit, it won't be at all dangerous. You can be as paranoid as you like from then on. I'd just pull the drill out while keeping my face out of the line of fire. But then, I spend half my time looking into pressurised furnaces. So my risk acceptance is somewhat higher than most!

Brilliant. Thanks. I'd hate to ruin my rugged good looks.

  • Haha 2

If you're friendly with a workshop that has a large scraps bin you can always ask to dispose of there.

Otherwise theres always the places like sims metal etc depending where you are at
https://recyclingnearyou.com.au/cars

  • Like 1
12 hours ago, Aggroman said:

If you're friendly with a workshop that has a large scraps bin you can always ask to dispose of there.

Otherwise theres always the places like sims metal etc depending where you are at
https://recyclingnearyou.com.au/cars

Great link. Thanks! 

On 26/11/2024 at 8:27 PM, PranK said:

It was the pressure I was worried about. @GTSBoy does drilling them pose any problems?

Depends on who you ask.

For the large part, you should be fine.

Nissan had us use a special tool on boot gas struts to release the pressure as apparently drilling could be dangerous. Could just be the excess pressure and possibly of blowing swarf into your face.

Normally, we have never worried about releasing pressure before disposal. 

13 minutes ago, luke gtr said:

Nissan had us use a special tool on boot gas struts to release the pressure as apparently drilling could be dangerous. Could just be the excess pressure and possibly of blowing swarf into your face.

Gas springs (ie boot/bonnet struts) will be charged up to about 200 bar. That's a bit scary. Suspension dampers will have maybe 10 bar of N2 pressure, which is just a sneeze, where I come from.

Anyone drilling holes in anything, pressurised or not, without wearing safety glasses deserves swarf in the eyes.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...