Jump to content
SAU Community

Recommended Posts

Nice bit of history. WTF are a csp311 (Fairlady?) and an S30 ? I've looked in Wiki but it is a bit sketchy.

CSP311 is very early Silvia:

http://members.ozemail.com.au/~finden/DSOA-SILVIA.html

S30 is Nissan model series speak for 240Z/260Z/280Z (note: NOT 280ZX which is S130 model series)

Edited by SteveL
  • Replies 104
  • Created
  • Last Reply

Top Posters In This Topic

Ok Some more history nobodys mentioned so far.

In 1974's Hardie-Ferodo 1000 at Bathurst, A 240K was raced by Stewart McLeod and Doug Whiteford. It came second in its class (class C, class winner was an RX3) and 7th outright.

Unfortunate that Nissan didn't have the smarts to quietly ship / sell enough cars with appropriate upgrades.

The McLeod/Whiteford car was a bog stock GL, basic L24 intake manifold, tiny exhaust, sedan/hardtop springs & dampers, 250mm front discs etc.

The GT intake manifold might have only been good for a small power increase but that would have been enough for a few tenths a lap.

Ditto the brakes, the 270mm discs were available but not fitted to the Australian market car so couldn't be used. How much gain? Hard to quantify but probably in the order of a second a lap or so.

Suspension from the GT would have reduced the awesome body roll across Skyline and through the Dipper which had to be worth a few tenths!

All up enough to have kept the Mazda RX3 behind.

You really had to see the thing running to appreciate how bad it was and just how good McLeod & Whiteford were to keep the shiny side up.

Then Mazdas wouldn't have led the class and the whole history of Nissan in Oz would have been different.

But then again, the current Nissan 350z 'supercar' is a big yawn and the scant info leaking on the next Skyline indicates it will be an even bigger yawn, if not a technicolor yodel.

Unfortunate that Nissan didn't have the smarts to quietly ship / sell enough cars with appropriate upgrades.

The McLeod/Whiteford car was a bog stock GL, basic L24 intake manifold, tiny exhaust, sedan/hardtop springs & dampers, 250mm front discs etc.

The GT intake manifold might have only been good for a small power increase but that would have been enough for a few tenths a lap.

Ditto the brakes, the 270mm discs were available but not fitted to the Australian market car so couldn't be used. How much gain? Hard to quantify but probably in the order of a second a lap or so.

Suspension from the GT would have reduced the awesome body roll across Skyline and through the Dipper which had to be worth a few tenths!

All up enough to have kept the Mazda RX3 behind.

You really had to see the thing running to appreciate how bad it was and just how good McLeod & Whiteford were to keep the shiny side up.

Then Mazdas wouldn't have led the class and the whole history of Nissan in Oz would have been different.

But then again, the current Nissan 350z 'supercar' is a big yawn and the scant info leaking on the next Skyline indicates it will be an even bigger yawn, if not a technicolor yodel.

I thought the Australian 240K GL hardtop was a GT spec, but badged as a GL because of the GT paranoia that was going on at the time, caused by holden and fords plans for high powered street cars (XU-2 and Phase 4 GTHO). In the Parts manual the badges are shown as GT badges for the home marker, but there are GL badges marked as "for Australia" on the same page for the same model. Also I have reviews from magazine articles at the time that state the Aussie 240K GL is actually a GT model.

I'd be interested in knowing what the differences are between a JDM GT and and Aussie GL are apart from what you have already mentioned

What's the GT intake manifiold look like? I just picked up a 240K hardtop, but it has interior GT badges instead of GL. All external badges are missing.

WTF are a csp311 (Fairlady?) and an S30 ? I've looked in Wiki but it is a bit sketchy.

Eveybody else was posting chassis codes, so i did too.

CSP311 is the chassis code for the 1st generation Silvia (1965 to 1967).

Mines been modified a bit, some time before I got it.

IMG_0002Small.jpg

S30 is a 240Z.

  • 2 weeks later...

I know you have already seen these on another forum but attached here so other people could see the difference too.

Love that little CSP311 Sylvia! I last had anything to do with one of these when I owned a late '66 way back in '68.

post-30643-1160545272.jpg

post-30643-1160545295.jpg

  • 4 months later...
i don't know if this will help as the r30 was produced in OZ as well as imported in small numbers?

the MR30 was the australian version, HR and DR were the japanese made sports versions produced in both 2 and 4 door examples, 81/82 the HR was built as an entry level sports car basic turbo inline sohc 6 cylinder producing around the 150-160bhp with a weight of around the 1150kg mark for the 2 door and only slightly more weighty in the 4 door, this car was raced both in japan, the USA and here in australia with "gibson motor sport" being the main surrporter of the skyline here in OZ, in the US Paul Newman took a liking to the car and raced it with much success there, this in turn lead to Nissan japan producing a limited # of "Paul Newman" HR30 skylines both in the 2 and very rear 4 door versions, still running the inline 6 but it produced around 170-180bhp. i don't know what year production of the HR stopped as in 1982 Nissan began production of the DR30....

the first of the DR range i believe was a N/A fj20de powered car about 160bhp, the car itself had quite a few differences to the HR, it had all the "mod cons" radio, a/c, power windows and central locking which in turn made the DR about 100kg heavier than the HR, this trend seemed to follow in the next versions of the DR as well. the RS DR30 was a step up from the N/A version as it was powered by the fj20det at around 180-190bhp not to many changes other than the turbo and a brake upgrade though, some may have had a factor sun roof? then in 83/84 Nissan went that extra step forward and revamped the DR30 skyline into something that will turn heads even today.. the RS-X DR30, for starters the intercooled fj20det produced 205bhp and was the most powerful production car produced by Nissan, the look of the car was changed to a more aggressive looking no grill smaller headlights sharper front profile, "tekemon" or "iron mask" was what it was refered to by locals. all of these models have made there way over to australia at some point and are still being shipped today...

they were the beginning of what is now refered to as the "wedge shape" skyline, 6th generation skyline.....

sorry for the hi-jack

i always thought the "iron mask" was translated from Hakosuka

sorry for the hi-jack

i always thought the "iron mask" was translated from Hakosuka

Iron Mask (Tekamen) was the nickname the Japs gave to the facelifted DR30 front end, it has nothing to do with Hakosuka at all (which means "box skyline").

this is by far the best explanation of the phenomenon I've found, from an old issue of J's Tipo magazine on Kev's DR30 site (which has since disappeared):

In August 1983 the styling of the RS and RS-Turbo models were facelifted to further differentiate the super sports models from the other GT and TI Skylines in the range. The grille was deleted, and the bonnet now sloped down almost to the front bumper. The headlights were slimmer, and the engine breathed through two narrow slits. The overall appearance of the new RS models caused enthusiasts to nickname the new RS Iron Mask (or "Tekamen"), for its distinctive visage.
also a bit of DR30 history, probably already covered, and definitely not relevant...

Oct 1981: First DR30s released, 2000RS with FJ20E engine. Standard interior is stripped out with no mod-cons

Feb 1983: 2000RS Turbo with FJ20ET released. 2000RS N/A continues as per normal. Spartan interiors still standard equipment

Aug 1983: Facelift of R30 range. 2000RS Turbo becomes RS-X Turbo, 2000RS becomes (simply) RS. Interiors are now full luxury spec as standard

Feb 1984: FJ20ET intercooled version released. RS-X Turbo becomes RS-X Turbo C as a result

  • 2 years later...
There were 2 series of the GTS. Series 1 (all white with the rectangular tail lights) had 130kW, and Series 2 (all red with the round tail lights and white wheels) had 140kW. They rode on lowered Bilstein suspension, had the turbo front brakes, LSD, different cam, extractors, piggy back computer (maybe the first factory piggyback computer)

The Tasmanian police force had a few of them without any bodylit, but I believe they were otherwise the same spec.

All GTS's were Silouhettes, but not all Silouhettes were GTS's

I owned a GTSII for 7 years, and it was a beautiful car. Just the right amount of performance, comfort and style (and practicality).

I understand Nissan (or NSVD) also built one turbo one, to be the official pacecar at the Adelaide GP in 1989 or 1990. This car was for sale recently - I'd love to get my hands on it.

Hi, I owned this car for many years. Nissan NSVD TURBO Pace Car.

  • 4 months later...

Nice grab paul

the R31 Skyline was in fact built in Clayton/Westall were HSV makes their cars now. The RB30E was a reworked Z car motor with ECCS.

Import R31s are hard to come by these days even harder is the GTSR which was a Group A racer with log xorst manfold for the turbo, bigger cooler, and called the RB20DETR only 800 were built so finding 1 is not hard but gettin it off the owner is another problem.

Another R31 is the Passage GT pretty cool looking sedan without B pillars and the GTS, GTSX coupes compleated the line up and with a range of options like autospoiler which comes down at 80kms, rain sencing windsheld wipers and a slew of other options.

RB20E, RB20S, RB20DE, RB20DET, RB20DETR and RB24E

  • 5 months later...
I thought the 240K was introduced to Aus in 1973 - but you say cazz your dad bought one in 1972. Can you confirm this? The C110 model started production in late 1972 but I thought it wasn't until 1973 that the hardtop "240K" was shipped over to Aus. Later in June 1974 the 4 door sedan was introduced.

I'd like to talk about the interesting badging of the car, and how it was quickly changed from a 240K GT to a 240K GL. Early pictures for promotion show the car with NO "240K", "GT" or "GL" badges at all - just Datsun (notice the first picture Jim posted). I assume this was because they didn't have the badges at the time of photoshoot. From what I can gather the car was initially sold here as a GT, but only for a couple of months maybe. Then it swapped to GL, to try to attract lower insurance premiums. The car was exactly the same, except I've heard that the manifold was slightly different?? I think the rear quarter "Datsun" script badge changed at the same time as the change from GT to GL, too.

Cazz, do you remember if your dad's was a "GT" or a "GL"?

I have two 1974 240K 2-doors, both are plated as 240K GL, but one of them has 240K GT door trims and different tail lights (same as Jap spec)

I have two 1974 240K 2-doors, both are plated as 240K GL, but one of them has 240K GT door trims and different tail lights (same as Jap spec)

Got any pics Ben? i have been looking for a coupe for a while and have had no such luck and you have two, luck man.

  • 7 months later...
1982 is where the r30 began....you would have to ask the guys in the r30 thread about that one.

have a look in my gallery...its chockers of c210/c211 pix

EDIT: Also check out my thread "c210/c211 skylines" for full history of this model

hi there i notice you sold all c210 skyline to saudi arabia is that a hard process

  • 2 weeks later...

Hello everyone.

My name is Jorge, I live in portugal and I'am the proud owner of a 1972 Nissan Skyline C-10 2400Gt !

The car was discovered about 2 years ago in Funchal ( Madeira Island ), inside a garage stopped for almost 18 years....

The car was a service car, from the local 70's Nissan Representative there, and was only used in very few ocasions and then left to rest in the garage...It only has about 7.500 km's on the odometer, when it was discovered the car only had about 6.500 km's marked !

I also have more Japonese Classic Cars, like a Datsun 510 1600SSS from 1971 and a Toyota 2000 GSL Sedan, also from 1971, both in top condition.

You can find photos from my car and many more info about it and early Skyline models in Europe and else were, by following this treat at :

http://www.classiczcars.com/forums/showthr...;highlight=c-10

Regards from Portugal

Jorge

Edited by 2400GT

And here's some recent photos of the car in the Portuguese Vintage Classic Motorshow, last 21th of March, 2010 :

http://www.classiczcars.com/forums/showthr...5183#post335183

Regards

Jorge

Edited by 2400GT
  • 7 months later...

Every now and then i think it would have been better to save and get an R33...

but then i read this and it makes me smile. haha.

and why are VNs being mentioned!?! i know this is an old thread but u can buy 5 of them for $400 and make one roadworthy car. but it will still be a VN

  • 5 months later...
  • 6 months later...

ok iv got a nissan,p230/datsun 240c hardtop,1971,i think where it says modle it has a K stamped,am i to understand correctly that what makes a nissan skyline is the offical taging or gt which became gl badging or is there a little more to it,this car has 4 on the floor and runs a L24 hitachi carb,can anyone tell me more about this car and if it fits into the skyline group. :rolleyes:

I'm a little confused, but I think you are asking three separate questions, which I'll address in turn.

If I read this correctly the VIN stamped on the firewall of your car features the letter K. This has nothing to do with the 'family' of the car. From memory (I don't have my owners manual in front of me), for the Cedric range the 'K' denotes hardtop, which is what you have. There was a model of Skyline from 72-77, the C110, which was sold in Aust as the Datsun 240K. Maybe this is where the confusion lies, but they are totally separate cars.

To the best of my knowledge none of the Cedric family were ever badged as GT cars. Moreover, many Skylines were not badged as GT models either. Australian model Skylines in the 70's were badged as GL, while the same car in Japan was badged as GT. There are many theories about why, but in short these two letters don't denote whether you have a Skyline or not.

Finally, you have a car belonging to the Cedric family. Although they ran the virtually same L24 and what I believe to be an interchangeable transmission with the Skyline/Datsun 240z, the differences in the body, interior, suspension, and differential make it quite a different car to drive.

They are extremely cool, but a currently a bit of an unloved classic in Australia.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...