Jump to content
SAU Community

Recommended Posts

AWD more likely to stick to the road............4 points of traction means more resistance....therefore grip

and less power being transferd to more wheels also eases traction problems

GTR was designed to win races, it did that to an almost unprecedented ability.............

think bathurst.............aussie RWD cars spinning about in the wet while the GTR was lapping them.........

i hope that helped......................you better not be one of those 13 yearolds who think GTR's are crap cause they're not 'drift spec'

All GTR's have ATTESA E-TS, 4 wheel drive system consisting of a variable electronic torque-split transfer mechanism. This directs torque to the front drivetrain through a multiplate clutch.

The clamping force on the clutch can varie between 0-50% dependant on wheelspin sensors that measure slip in the rear wheels. GTR is basically rwd intil you accelerate hard and the ecu signals the front wheels kick in.

:)

GTR's are NOT AWD!!!

I know what your saying, but I think "AWD" has come to signify cars like the GT-R (and numerous others: Honda CR-V for instance) that have a bias to either front or back, and engage the other set of wheels depending on conditions. This is distinct from "4WD" which implies some sort of constant drive delivered to all wheels (nobody mention the 1% going to the R33 GT-R's front :) ).

LW.

In the "GT-R Memorial" book (Japanese publication chronicling the life of the GT-R) is says the GT-R is *4WD*. I understand what you guys say about AWD, but that term isn't used in conjuction with GT-Rs in Japan.

It's pretty simple, RWD has some disadvantages on track, the biggest being power on oversteer out of corners. 4WD was used in the GT-R simply to be able to get the power on ealier out of corners therefore reducing track times... and as what has already been stated, quicker lap times is what the GT-R is all about (without going to a MR platform for better weight distribution).

In the "GT-R Memorial" book (Japanese publication chronicling the life of the GT-R) is says the GT-R is *4WD*. I understand what you guys say about AWD, but that term isn't used in conjuction with GT-Rs in Japan.

The distinction has only really been made by the Australian motoring press (and marketers) in the last two or so years as Australia has seen an explosion in the 'soft-roader' market.

These terms are obviously location specific and rather fluid :)

LW.

The distinction has only really been made by the Australian motoring press (and marketers) in the last two or so years as Australia has seen an explosion in the 'soft-roader' market.

These terms are obviously location specific and rather fluid :)

LW.

Right, but the maker could've used any term to describe the drivetrain for their car, but decided on 4WD... why was that?
Right, but the maker could've used any term to describe the drivetrain for their car, but decided on 4WD... why was that?

Rezz, I am not disputing what you are saying, in fact I think the AWD/4WD distinction is pretty stupid because it means different things to different people. But rather than writing 'full time 4WD' or 'variable 4WD', the writers of motoring mags/papers now just use the 4WD and AWD respectively. Thus they have entered the Australian lexicon with particular meanings.

I imagine the distinction was originally made so that companies in Australia couldn't be sued for suggesting that their 'soft-roader' cars had real off-road ability (which, arguably, the 4WD tag might imply). By creating the new 'AWD' class, they have effectively tried to meld the idea of the safety of 4WD traction without the ability to go off-road (and perhaps also, the negative conetations attached to big offroaders re fuel, etc).

LW.

the writers of motoring mags/papers now just use the 4WD and AWD respectively. Thus they have entered the Australian lexicon with particular meanings.
Sorry mate, I don't live in Australia... and it's starting to show :)
Sorry mate, I don't live in Australia... and it's starting to show :)

No need to apologise -- as I said, its a stupid marketing driven distinction and is highly confusing (in fact, if I was a cynical bastard -- which I am -- I might suggest the confusion is intentional). Besides which, we all know Japan is the place to be ;)

LW.

"Off road" 4wd like Landcruisers etc don't have

That's funny, Toyota thinks it does:

Constant 4WD

When driving over dramatically different surfaces, confidence is inspired by the constant four-wheel drive. Any sudden emergencies, such as driving through a slippery surface, are more easily controlled with LandCruiser 100's constant 4WD.

Traction control is standard on all Sahara models to provide added grip off-road

think bathurst.............aussie RWD cars spinning about in the wet while the GTR was lapping them.........

Hi... ummm maybe you should watch Bathurst 1992...

Any difference between AWD and 4WD are purely a marketing terms.

The lower spec models (GTS-T, GT-T) are all RWD.  

Why did Nissan decide to make the GTR an AWD car?

because when they made a rwd prototype it was too fast. they added the wieght of 4wd to slow it down :)

No matter fulltime or part time...GT-Rs are still considered 4WD. In racing they are only allowed in 4WD class or over 2000cc turbo class with other cars or only GT-R class.

4WD and AWD is pretty much interchangable these days as mentioned lost due to marketting. In some Evo brochures from MMC sometimes it reads AWD but on the rear window of the car is says 4WD. Does it really matter these days!

"Off road" 4wd like Landcruisers etc don't have

toyota landcruisers have both part time 4wd and constant 4wd from late 90 on ( 80 series) the gxl and more upmarket saharas and gxvs have contant 4wd , the bottom of the range ( barn doors at the rear and vinyl seats , yuk) are still part time 4wd you have to select by moving a lever next to the normal gear lever .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...