Jump to content
SAU Community

Recommended Posts

Do you mean me.   No  I have  Nismo 555cc  and  with 384rwkw runningout of fuel a bit so we have converted to twin fuel filter for less restriction adn turning up the fuel pressure a bit.

Waiting for the Skyline come back about non fast ones in town??  Anybody>> Where is  wreckedhead?

im here, the R will be back on the track soon enough, just waiting for some time to get the cage in, been sitting in the rain for weeks now, but will get the eventually.

  • Replies 97
  • Created
  • Last Reply

Top Posters In This Topic

DezertEagle should be fine as long as you have not boosted it too hard. Run some octane booster to be safe, but drags is usually no probs, circuit racing brakes and temps go up and more need to have good car and set up. See you out there.

OK I put rego on the zed but the plates don't weigh that much to worry about, and show me a registered car at the drags that runs a cat? Be interesting to run Theo and get him to disconnect his front drive shaft.

Also Paul my boss never lets me go but does not stop me and you only have one kid. A cute one too. Being cheeky again if you can make it, your beast will be the king and toughest looking car there, but that's only my opinion. Plus if not aloud out too much this is the night. I hope weather will be ok.

I noticed a little bit of wheel spin in the wet today and checked my tyres. The rear left is basically bald, how tough are the pits check at EC? I dont want to waist my time just to get rejected at the pits.

John has convinced me to give the new R34 a run this Wed, providing the Boss and work allow me to be there, I will come down for a run.

careful mate you don't want to enjoy it and start batting for the wrong team :D

We need another trackday....soon....

Guest two.06l
I noticed a little bit of wheel spin in the wet today and checked my tyres. The rear left is basically bald, how tough are the pits check at EC? I dont want to waist my time just to get rejected at the pits.

the only bald tyre at the drags is a slick, you would be wasting your time and money racing on that. Put a ad in the wanted section to see if anybody has something more suitable to race on. Paul...DIRTgarage

I noticed a little bit of wheel spin in the wet today and checked my tyres. The rear left is basically bald, how tough are the pits check at EC? I dont want to waist my time just to get rejected at the pits.

What size tyre are you after Paul ?

I have 1 265x35x18 about 80% tread from memory, let me know if you are interested .

Paul if your engine falls out then I might listen otherwise get there, and put your lipstick back in your purse. Or was some wimp from work posting for you?

Paul if your engine falls out then I might listen otherwise get there, and put your lipstick back in your purse.  Or was some wimp from work posting for you?

LOL...talk it up funboy:) ...you wont be cracking wise when you jump in your car for a run and you see a horses head in the passenger seat...uh, err drag queens take these things personally

Paul if your engine falls out then I might listen otherwise get there, and put your lipstick back in your purse.  Or was some wimp from work posting for you?

Sheesh John finally gets through a day of motorsport without his motor imploding and he gets a bit cheeky!




  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...