Jump to content
SAU Community

Recommended Posts

Do you mean me.   No  I have  Nismo 555cc  and  with 384rwkw runningout of fuel a bit so we have converted to twin fuel filter for less restriction adn turning up the fuel pressure a bit.

Waiting for the Skyline come back about non fast ones in town??  Anybody>> Where is  wreckedhead?

im here, the R will be back on the track soon enough, just waiting for some time to get the cage in, been sitting in the rain for weeks now, but will get the eventually.

  • Replies 97
  • Created
  • Last Reply

Top Posters In This Topic

DezertEagle should be fine as long as you have not boosted it too hard. Run some octane booster to be safe, but drags is usually no probs, circuit racing brakes and temps go up and more need to have good car and set up. See you out there.

OK I put rego on the zed but the plates don't weigh that much to worry about, and show me a registered car at the drags that runs a cat? Be interesting to run Theo and get him to disconnect his front drive shaft.

Also Paul my boss never lets me go but does not stop me and you only have one kid. A cute one too. Being cheeky again if you can make it, your beast will be the king and toughest looking car there, but that's only my opinion. Plus if not aloud out too much this is the night. I hope weather will be ok.

I noticed a little bit of wheel spin in the wet today and checked my tyres. The rear left is basically bald, how tough are the pits check at EC? I dont want to waist my time just to get rejected at the pits.

John has convinced me to give the new R34 a run this Wed, providing the Boss and work allow me to be there, I will come down for a run.

careful mate you don't want to enjoy it and start batting for the wrong team :D

We need another trackday....soon....

Guest two.06l
I noticed a little bit of wheel spin in the wet today and checked my tyres. The rear left is basically bald, how tough are the pits check at EC? I dont want to waist my time just to get rejected at the pits.

the only bald tyre at the drags is a slick, you would be wasting your time and money racing on that. Put a ad in the wanted section to see if anybody has something more suitable to race on. Paul...DIRTgarage

I noticed a little bit of wheel spin in the wet today and checked my tyres. The rear left is basically bald, how tough are the pits check at EC? I dont want to waist my time just to get rejected at the pits.

What size tyre are you after Paul ?

I have 1 265x35x18 about 80% tread from memory, let me know if you are interested .

Paul if your engine falls out then I might listen otherwise get there, and put your lipstick back in your purse. Or was some wimp from work posting for you?

Paul if your engine falls out then I might listen otherwise get there, and put your lipstick back in your purse.  Or was some wimp from work posting for you?

LOL...talk it up funboy:) ...you wont be cracking wise when you jump in your car for a run and you see a horses head in the passenger seat...uh, err drag queens take these things personally

Paul if your engine falls out then I might listen otherwise get there, and put your lipstick back in your purse.  Or was some wimp from work posting for you?

Sheesh John finally gets through a day of motorsport without his motor imploding and he gets a bit cheeky!




  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...