Jump to content
SAU Community

Recommended Posts

after much deliberation amongst the mods we've decided to ban him. but we're quite sure he'll sign up again under a different username, so till the next installment of "fun with alex"... stay tuned, same forum, different month.

  • Replies 77
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

after much deliberation amongst the mods we've decided to ban him. but we're quite sure he'll sign up again under a different username, so till the next installment of "fun with alex"... stay tuned, same forum, different month.

Cant wait!!! :wassup:

Sorry guys, im a little slow (Must be all the ELF ive inhailed in the past few weeks :D) but is/was this the same mines_datsun in the bad traders section?

here is the link:

http://www.skylinesaustralia.com/forums/sh...ead.php?t=33686

and here is the short version

Known Nickname(s): Mines_Datsun, LaL

Full Name: Alex Kantarovski

Email: [email protected]

Phone(s): 0403 715 527, 0400829787

Address: Taylors Lakes, Victoria

Surely a better way is to randomly check all new members? Sorry, im no i.t guy, dont know the enormity of that task.

dats him..

Well I can let out a :D .. until next time. Who will it be? Where will he post? Will he clever next time? Will he start off with a random jibe here, a random jibe there and then erupt into full explosive diorhea?

Will he win SAU's Tool of the Year award (STOTYA) for 2003/2004?? - two years running!!

Just ban his IP address so he cant get on full stop

Make it just say "You do not have persmission to view this board"

and thats it :D

by the way, went to my friends place, he is Lankan. Had some curry. Tastes awsome and is hot as :D

So shut up REDFC, woops sorry you will be shut up for a while now :D

HA HA HA HA HA HA HA HA HA AWWWWWWWWWWWW WHAT A SCREEM THIS ONE I GOT TO PIN UP AT SELECTMAZ HAHAHAHA SO FUNNY

god ive been building rotorys for a while and belive me this is the funny thing we have herd of all week 1000HP oh so funny please guys if this was the case we must be all fools hahahah ban the fool

No.. this aint funny.

Horus a GT3540 will give you 10psi of boost @ 3500rpm on a extend port rotor with hks manifold.

i never said 1000hp rotor's are easy to make, i just said that is allot easier to get a rotor to 1000hp then a piston engine.. big deal , guys grow up.

and you folks said that the VIC section was dead...

oh and alex, if you're reading this, I just gave you a temp ban to save you the hassles of making up another username and us trying to track you down. THe ban expires in a week, use your time wisely to contemplate why you've now been banned from both NissanSilvia and SAU

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...