Jump to content
SAU Community

Recommended Posts

I want to buy my partner wheels for his R33 GTR skyline can you please help with a few questions - Do the rims need to be the same width all round? Or can you use narrow rims on the front with the same width tyres? Also if going to 19” rims what size tyres should I get him?

I have spoken to a major tyre shop and they were very unhelpful. Thank you very much!

Link to comment
https://www.sau.com.au/forums/topic/57911-girl-needs-help/
Share on other sites

Guest two.06l
Thank Richard!! The rims will probably be 8.5" so what size would you suggest??

P.M. Wreckedhead as he has R34 GTR rims with tyres ready to go. Its widely recognised that these rims look hot on a 33 GTR.Heres a link. http://www.skylinesaustralia.com/forums/sh...ead.php?t=56621

Link to comment
https://www.sau.com.au/forums/topic/57911-girl-needs-help/#findComment-1113434
Share on other sites

JustJap also have a set of R34 GTR rims for $3K (they're 18x9) and look hotness.

For 9" wide you should get 235's stretched, or 245's. I'd get the 235's stretched as there's no sidewall flex, problem with this is that you gotta make sure you know how to park otherwise you'll gutter rash them to hell and back.

Link to comment
https://www.sau.com.au/forums/topic/57911-girl-needs-help/#findComment-1113454
Share on other sites

Don't get 8.5" wide, get at least 9" wide since thats stock width, OR 10" wide fit as well..

same size wheel AND tyre all the way around...

Go witha good brand, not something cheap like ANZ etc... It may be worth asking your bf what he wants, it would suck to spend 4k on wheels/tyres to have your bf not really like them :D

Link to comment
https://www.sau.com.au/forums/topic/57911-girl-needs-help/#findComment-1113465
Share on other sites

Thank Richard!! The rims will probably be 8.5" so what size would you suggest??

no worries, happy to help PK.

Like the other lads said, I'd suggest 9inch wide +. For me I think 18X9 is a good size for a 33GTR and the tyres will be a little more affordable than for the 19s. If he's really keen on some BIG wheels though, then 19s would be the way to go.

happy wheel hunting.

Richard

Link to comment
https://www.sau.com.au/forums/topic/57911-girl-needs-help/#findComment-1113490
Share on other sites

I second/third that you will need all the same all around.

I also think that if you're going to the trouble to get new wheels for him that they should be wider. 9" or 10" would look really hot, especially with a 235 or 245 width tyre stretched across them.

I'm not sure about offset as I've never owned/fitted a skyline let alone a GTR!

Link to comment
https://www.sau.com.au/forums/topic/57911-girl-needs-help/#findComment-1113493
Share on other sites

If your going for a 19 inch rim best bet would be to go for a 19x91/2 with a offset of plus 11 for a 33 or 34 GTR and the correct tyre is a 275/30ZR19 this will give you the closet to the correct height this is what Rays Engineering recommand for a 33 or 34 GTR, for 18 inch most use 18x9 with a 265/35 tyre i wouldn't go under 245 as this is what 33 and 34 GTR's came with so if you wanted to keep costs down go for a 245/40ZR18 . Also the PCD is 114.3

Link to comment
https://www.sau.com.au/forums/topic/57911-girl-needs-help/#findComment-1113971
Share on other sites

r u guys sure the wheels have to be the same size? cosa the ones on my car are 8.5 on the front with 9.5 on the back, with 255s all round

and the tyre placard says the tyres are different sizes, like rear was about 15mm wider, can't remember exactly what size, i'll have to check tomorrow

Link to comment
https://www.sau.com.au/forums/topic/57911-girl-needs-help/#findComment-1114073
Share on other sites

Nuh if you have different widths on a gt-r the attesa 4wd can stuff up. All gt-rs should have the same width wheels

yeah the torque split gauge goes crazy. It happens on a friends car who has different sizes.

As for the 19's I agree with gtr13, go for 275/30/19 on 9.5 inch rims.

Link to comment
https://www.sau.com.au/forums/topic/57911-girl-needs-help/#findComment-1114200
Share on other sites

I thought the GTR's came with wider on the back standard.

This is what I've seen on every GTR.

Could you show us the GT-Rs you've seen with different wheel widths front and rear? It's possible you saw GTS-ts or GTS25t's that had GT-R badges on them... not GT-Rs.
Link to comment
https://www.sau.com.au/forums/topic/57911-girl-needs-help/#findComment-1114299
Share on other sites

hmm you're looking at a big tyre bill.

thats for sure, especially for 19" rims. I would go for 265s at least...depending on how much hp the car has or will have. Cost big $$$, but has a sweet footprint.

I have 265's all round on my gts-t (bit of over kill seeing as only driving the rears) but looks hot with the wide treads.

Link to comment
https://www.sau.com.au/forums/topic/57911-girl-needs-help/#findComment-1114773
Share on other sites

Hey guys, thankyou all VERY much, you'ra great!. Just one more question - Is there a measurement or what is it called when one wheel looks narrower but isn't - sorry if this doesn't make sense, but at the moment the car has the same size rims on it, but the spokes on the front wheels are closer out to the tyres, while the spokes on the back wheels are a lot deeper in.

Thanks again!

Link to comment
https://www.sau.com.au/forums/topic/57911-girl-needs-help/#findComment-1114780
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...