Jump to content
SAU Community

Recommended Posts

Stopped the backhand reach around method without even noticing. I think it came from driving the little Exige and Caterhams last year where there is no space in the cabin and you sit so low...no space for reach arounds is never a good thing :(

And Yes...something with E85 in the next two weeks :)

LOL, is that a rev up? Every mod I do I lose response :) Its a proven fact :)

I am only looking at running a 50% mix of E85. That way i can keep a 200L drum and just add 20L from a jerry can in my boot to 20L of 98 from the bowser. Will see just how sensitive the E85 is to moisture from storage :)

Not really all that concerned about gaining a lot. The car can make 285rwkws on 100RON, and i back it off a little to 255-265rwkws (on 98 I have to back it off to 245rwkws odd) for the track for when it gets hot. So with the better fuel i hope to be able to tune it up to 280rwkws and it still be safe on the track when oil/coolant, inlet temps all get hot.

Nah no rev up, alchohol based fuels tend to burn cooler the petroleum, so less heat in the manifold means less engery to turn the turbine.

But whether that is offset by being able to run more ignition advance, I dont know, there is no set science to it, some cars loose response and some gain.

But on the other hand the more advanced the timing the cooler teh EGT's (until it detonates) which wont help the situation

Hopefully you gain the respose back :thumbsup:

LOL, is that a rev up? Every mod I do I lose response :) Its a proven fact :)

I am only looking at running a 50% mix of E85. That way i can keep a 200L drum and just add 20L from a jerry can in my boot to 20L of 98 from the bowser. Will see just how sensitive the E85 is to moisture from storage :)

Not really all that concerned about gaining a lot. The car can make 285rwkws on 100RON, and i back it off a little to 255-265rwkws (on 98 I have to back it off to 245rwkws odd) for the track for when it gets hot. So with the better fuel i hope to be able to tune it up to 280rwkws and it still be safe on the track when oil/coolant, inlet temps all get hot.

how much psi were you running in the 245rwks track setup and your 285kw? on the vid u posted what power output was that? what kind of oil/coolant inlet temps do u see on street duties, and what do they change to on the track? i am curious as i have a similar setup and i havent had any track work yet but if i am planning to all this extra trialed and tested info is of great help.

Ita not all that scientific really. 21-20psi is the on 100RON is 280odd, 18psi with a few degrees of ignition removed is 245rwkws. The vid from Winton in December was 260rwkws on 100RON, the vid from last weekend is somewhere between 245-250rwkws on 98ron. Get your tuner to give it plenty of hits on the dyno under load with the water and oil temps up there and make sure the tune is fine.

My problem is my engine seems to take less ignition then it used to with the std plenum now I have the Plazmaman inlet so other engines may not be so sensitive to fuel and ignition. Well, at least mine never used to be so its either somehow related to the inlet or the engine is simply getting tired. Could be either really. I try not to run inlet temps over 95 for water on the track...no idea what my oil temp is tese days as i have never wired the sensor back up after my fire all those years ago. But typically stopped when my oil was at 110deg. These days not knowing what it is is i bet its getting up to 130deg on the track. On the street my water temp is usually between 70-75deg C

Nah no rev up, alchohol based fuels tend to burn cooler the petroleum, so less heat in the manifold means less engery to turn the turbine.

Isn't this offset by you using 20% more fuel to reach the same total energy?

The very few cars I've done ethanol blend tunes have ended up with better overall power delivery, potentially slightly better spool but I don't stress too much about the boost curve so much as power delivery. All that should matter is more torque everywhere :)

nice vid bris. love to see you out there mate. we both need to do someting about seats. I notice both mine and your seats move around A LOT in the top half. short of tagging the thing to the main hoop of the cage what can we do to stifen the buggers? It may also be our awesome physiques?

looks like you've got the radcam dialed in nicely now too. fking thing.

Well, now that I am back in Aus and the car is back together. I am goign to keep this thread alove :)

So did two track days in two weekends. Did two laps at Sandown and got booted because of noise :( So the following weekend went to Winton and gave it a wrap...

The basics were 19psi, 245rwkws and shifting between 7,400-7,600rpm for 43 laps. I have lost a bit of power as United have stopped selling 100RON so had to wind some ignition of it. Its amazing how sensitive my engine is to ignition, it really loses and gains power with a few degrees....so need to look at getting back on a better quality fuel. Before the plenum install i ran 98 plenty of times on the 100ron tune and no issue.

nice vids! can't believe they kicked you outta sandown, its not that loud!

...with the 6boost manifold and Turbosmart gate it is a lot higher pitch then it used to be, and perhaps a little louder. So they used to ping me eyars ago before I went OS with work. Seems upon my return they again care about loud cars :(

Your seat base isnt oo big a problem Count, its the Momo rails you are using on the base. Throw the Cobra rail on Frankenbase and it will be rigid again :) (O think/hope)

...with the 6boost manifold and Turbosmart gate it is a lot higher pitch then it used to be, and perhaps a little louder. So they used to ping me eyars ago before I went OS with work. Seems upon my return they again care about loud cars :(

any upcoming trackdays? i might come down for a look at your beast in action :)

...with the 6boost manifold and Turbosmart gate it is a lot higher pitch then it used to be, and perhaps a little louder. So they used to ping me eyars ago before I went OS with work. Seems upon my return they again care about loud cars :(

Your seat base isnt oo big a problem Count, its the Momo rails you are using on the base. Throw the Cobra rail on Frankenbase and it will be rigid again :) (O think/hope)

Stick a muffler on the end of the gate?

Ita not all that scientific really. 21-20psi is the on 100RON is 280odd, 18psi with a few degrees of ignition removed is 245rwkws. The vid from Winton in December was 260rwkws on 100RON, the vid from last weekend is somewhere between 245-250rwkws on 98ron. Get your tuner to give it plenty of hits on the dyno under load with the water and oil temps up there and make sure the tune is fine.

My problem is my engine seems to take less ignition then it used to with the std plenum now I have the Plazmaman inlet so other engines may not be so sensitive to fuel and ignition. Well, at least mine never used to be so its either somehow related to the inlet or the engine is simply getting tired. Could be either really. I try not to run inlet temps over 95 for water on the track...no idea what my oil temp is tese days as i have never wired the sensor back up after my fire all those years ago. But typically stopped when my oil was at 110deg. These days not knowing what it is is i bet its getting up to 130deg on the track. On the street my water temp is usually between 70-75deg C

thanks for the info roy, have you taken your car down the strip before/after the plazmaman or other mods? if so whats the best time you have got with what setup? plazmaman plenum was my next upgrade but after hearing what you have said i am now hesitant

Edited by Yts

One bad result doesnt mean the product isnt any good. There could be a few reasons why I didnt yield better results. There is evidence that if i throw my Tomei cams in, the 10cm housing at it that I aill make way more power up top then I ever could with the std plenum...but seems to not be able to match the torque/response of the std plenum. For my car the compromise doesnt seem to have worked out well.

I have taken the car down the qtr years ago with about 235rwkws and RE55s. I ran a 12.9 at 114mph with a 2.3 60ft time. I walked the car off the line as I am still running a std RB20 gearbox. That box now has 205,000kms on it so I try to look after it with launches and shifts, it probably had about 180,000kms on it when i ran that time. With a proper go in first and second gear trying to get the 60ft time down to 2.0sec or better then there is a pretty easy low 12 in it. And that time was with this tune...

Dyno_RacePace.jpeg

I still remember racing you all night @ Calder, fun times.

:D

thanks for the info roy, have you taken your car down the strip before/after the plazmaman or other mods? if so whats the best time you have got with what setup? plazmaman plenum was my next upgrade but after hearing what you have said i am now hesitant

You've gotta weigh up cost vs gain, the plenum itself + retuning etc is basically RB25 motor money.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...