Jump to content
SAU Community

Recommended Posts

Heya,

How easy is it to tell a CF bonnet (sprayed white) from a normal bonnet?

Also, are there any legal ways to get a vented bonnet so as to not get defected?

Ohh, whilst on topic of legality.. does NSW have the 1 intake mod rule? and if i still have stock intercooler, does the pod still need to be boxed? A partition is not a box right? lols

thanks

- Eric

Link to comment
https://www.sau.com.au/forums/topic/59585-bonnets/
Share on other sites

Heya,

How easy is it to tell a CF bonnet (sprayed white) from a normal bonnet?

Also, are there any legal ways to get a vented bonnet so as to not get defected?

Ohh, whilst on topic of legality.. does NSW have the 1 intake mod rule? and if i still have stock intercooler, does the pod still need to be boxed?  A partition is not a box right? lols

thanks

- Eric

when he goes to open your bonnet to check out your engine bay I *think* he may notice that it ways about a quarter of what a normal bonnet does. That may give the game away...

Link to comment
https://www.sau.com.au/forums/topic/59585-bonnets/#findComment-1137867
Share on other sites

This may, or may not concern anyone but I've always wanted a aluminium bonnet for my car because of the weight saving and legality/practicality.

CF is great on a track but imagine hitting someone/being involved in an accident.

I imagine that stuff splinters, and as if someone being hit by a car isn't bad enough imagine the whole bonnet splintering into them, or into another car as it impacts you (or you impact them).

I think they're illegal for a reason, and unlike most stuff that's illegal to modify I think it's illegal for a good reason. Mind you having said that I've never seen one in an impact so maybe I'm over-dramatising.

*shrug* something to think about. (Oh and if you have insurance they might not pay you because your car isn't legal).

If you're comfortable with all that then go for your life - when I can afford it I will be getting an aluminium custom. As for you skyline boys I think you can just swap a GTR bonnet right?

Link to comment
https://www.sau.com.au/forums/topic/59585-bonnets/#findComment-1138632
Share on other sites

unless its in a legal rta document i wouldnt beleive a thing.
I'd have to strongly agree with that. It depends who at the RTA you call, what day and at what time as to the answer you get.

Basically just make sure you always have a jar of lube for your ass when you are out in your car...

:wassup:

Link to comment
https://www.sau.com.au/forums/topic/59585-bonnets/#findComment-1142815
Share on other sites

  • 3 weeks later...

Pod filters do not have to be in an airbox. Just get the thing engineered.

As for CF bonnets, I was always under the assumption that they are owner certified, meaning that they do not have to be engineered to be legal. Probably the best person to speak to would be an engineer. They'd be more consistent than the RTA.

Link to comment
https://www.sau.com.au/forums/topic/59585-bonnets/#findComment-1171716
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...