Jump to content
SAU Community

Recommended Posts

how do i get the Flutter sound on my s2 gtst?

i was at a wrecker and this guy came down changing gears letting off this cool flutter sound into the atmosphere

i asked the guy how he did it but he did go into much detail i guess he want to keep it a secert

he briefly said that he blocked off the BOV and he asked if i had a aftermarket air filter, he said thats all i needed to get that sound

i really wanted the flutter sound because it sounded MAD

i want to know if anyone knew how to do this?

Link to comment
https://www.sau.com.au/forums/topic/60655-flutter-sound-as-bov/
Share on other sites

  • Replies 300
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

What else do you need to know? As it was said, you just take off the standard BOV, block off the hole it leaves, and install an aftermarket pod filter on, and you'll get the same noise...

Most people seem to think its bad for your turbo (its what causes the flutter noise) and i agree with them.

well i got the fluttering noise on my car, its pretty sick, especially if you run full boost, thaz when its loud of its head.

When u do the "cooler noise" i call it, in front of ppl, every cnt looks at you mate. Its like you are a celebrity mate. but you gotta be carefull, read reasons below:

1) Attracts chix, but so does it the Cops

2) If you boost your car, you are more likly to blow it (been there done that)

3) it will stuff up your idleling, and in lots of cases your idel will be unstable, even if you go back to your original setup your idel remains unstable, as the AFM meter re-programs itself in a way.

4) ITS ADDICTIVE (trust me, once you put it on, you wont be taking it off)

P.S. To get it very loud, you should run higher boost, and have a big front mount cooler, and the POD, dnt worry about it, just run a 90 degree elbow from the turbo. and off you go.

Just be aware of the consequences below:

1) Get canary (defect sticker) easy as

2) Blow turbo

3) Very careful with this one, YOU MIGHT BE UP FOR A NEW BOTTOM END (been there done that)

The sound is wicked, but there are to many 'againsts' to have it on ya car. just get a after market BOV.

I had it on mine , I have a Blitz hybrid (atmo & plumb back) and had the plumbback blocked off as I did not have the right hose for it , it made a huge flutter sound ! but as everyone has said above it can cause serious damage to your turbo, suggest only using it for a short time !!!!!! if at all !!!

my 2 yen

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...