Jump to content
SAU Community

Recommended Posts

I have a problem with this ebc.

Followed the instructions, did exactly what it told me to do, I never done electronics since year 10, I'm 110% certain that I have the correct port.

So this is what I bought:

13092008069pl3.th.jpg

Finishing soldering connect 12v to accessories and earth to see that the ebc and hand controller are in good working order.

Turned the ignition on and I got black boxes, double checked everything to see if I had the correct port plug (which I did), could no make what the problem was.

On the IEBC the led closes to port (from this picture top right corner) was on, also the instruction manual says that IC1 has a dot and IC2 has a line but the chips on my kit didn't have that so swapped IC1 with IC2 while testing to see if this was the cause of my problem, and then some component fused out (don't no which one) so now I'm not getting power to the hand controller, included some high resolution pics.

14092008073pm7.th.jpg

14092008074np5.th.jpg

I still get the red led on but the big capacitor (bottom right, looks like a battery) does not heat up like usual.

You have got the chips the wrong way round. If you look on the instructions you will see that they both have the same PIC number but IC1 has written to the left , vertically, the number EZ8996 and

IC2 has printed left to right just below it (LINE) EZ8997 and these numbers are printed on the chips ...also can't see from your photo but cutouts on the chips have to go as per the printed diagram ( up for LC1 and to the left for LC2)

Other things to check (can't see from your photo) is that the jumpers should be left off (or removed) from LK1 and LK3 but the one on LK2 should already be in the right place. The usual reason for lack of display is that you need to turn the trimpot all the way up (clockwise I think).

If you think you have damaged a component you should be able to get a replacement from Jaycar.

There is a link that some people forget ( I can't see mine just now its in the car ) but I think there is one that goes undert the DB25 socket - I''l have a look when its daylight and check.

Some warnings: always plug in the hand controller before powering up. Also it seems a good idea not to switch between boost maps while powered up. (I plan to use one map only anyway). I have these kits for ages and have only just finished them (I would have bought them assembled if I could) but haven't got around to installing them so I will try to install at tleast the IEBC in the morning.

  • Replies 1k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Thx KiwiRS4T, I did plug the iebc with the hand controller before turning the power on and I adjusted the trimpod but all I got was boxes, in that pics I have the IC's in the wrong place but they originally in the correct place(I swapped them around just to check if the instructions were incorrect).

In regards to the Links you can adjust these even if your not using them

Anyway the PCB is melted from 12v, i think I left the low high boost in-between (i think), whats interesting is I didn't blown the fuse.

I have some question for my second kit!

The 3 red leds, do they go only one way as the diagram is showing A and flat side K.

The 22 crystalls (<X2 10Mhz> and <X1 20Mhz>) from the diagram the one closes to the port shows a link nex to the crystall and, bottom right shows the other crystall with links, are these supposto to be fused on?

The resistors, can they go both ways?

And last whats the trimpod on the IEBC used for?

Edited by LZY115

HI all

Hopefully someone can offer some advice as I have built the jaycar boost controller for my rb25det motor.

The issue I have is I cannot get a satble reading in run mode for the duty cycle. I have tried adjusting the trim pot but it is ether 1 or 64 and if I move the trimpot carfully I can get one point were the duty cycle just fluctuates up and down\. Everything else works???

any advice would be greatly apperciated as Ithe only info I can find is saying it can be uneven if you have peak hol;d injectors and havent found any info about you guys needing the adaptor for these???

Thanks

Ash

Thx KiwiRS4T, I did plug the iebc with the hand controller before turning the power on and I adjusted the trimpod but all I got was boxes, in that pics I have the IC's in the wrong place but they originally in the correct place(I swapped them around just to check if the instructions were incorrect).

In regards to the Links you can adjust these even if your not using them

Anyway the PCB is melted from 12v, i think I left the low high boost in-between (i think), whats interesting is I didn't blown the fuse.

I have some question for my second kit!

The 3 red leds, do they go only one way as the diagram is showing A and flat side K.

The 22 crystalls (<X2 10Mhz> and <X1 20Mhz>) from the diagram the one closes to the port shows a link nex to the crystall and, bottom right shows the other crystall with links, are these supposto to be fused on?

The resistors, can they go both ways?

And last whats the trimpod on the IEBC used for?

Sorry I am by no means an electronic expert. I built the controller myself but needed help for the other two. I know that the resistors can go either way and the trimpot in the IEBC is needed for fine tuning.

HI all

Hopefully someone can offer some advice as I have built the jaycar boost controller for my rb25det motor.

The issue I have is I cannot get a satble reading in run mode for the duty cycle. I have tried adjusting the trim pot but it is ether 1 or 64 and if I move the trimpot carfully I can get one point were the duty cycle just fluctuates up and down\. Everything else works??? ******Have you observed this while driving the car ? The duty cycle will not vary much in a no load (neutral) situation***

any advice would be greatly apperciated as Ithe only info I can find is saying it can be uneven if you have peak hol;d injectors and havent found any info about you guys needing the adaptor for these???

Thanks

Ash

I'm not the best person to give advice but I know that the RB25DET does not have peak hold injectors. 64 seems to be the default reading. Have you tried making adjustments with the buttons or pushing the reset button? I'm pretty sure the trimpot on the IEBC needs to be full on . (Actually have reread the instructions and the trimpot is needed for fine tuning.
HI all

Hopefully someone can offer some advice as I have built the jaycar boost controller for my rb25det motor.

The issue I have is I cannot get a satble reading in run mode for the duty cycle. I have tried adjusting the trim pot but it is ether 1 or 64 and if I move the trimpot carfully I can get one point were the duty cycle just fluctuates up and down\. Everything else works???

any advice would be greatly apperciated as Ithe only info I can find is saying it can be uneven if you have peak hol;d injectors and havent found any info about you guys needing the adaptor for these???

Thanks

Ash

Link 2 negative --- solenoid stays shut with 0% duty cycle and stays fully open at 100% duty cycle

positive --- solenoid stays open with 0% duty cycle and stays fully closed at 100% duty cycle

The manual recommends you leave it as negative, this may not be the case with your problem, also check if your actuator is a "normal open" or normally closed which is preferable.

Link1 and 3 should be left out.

Link 4 should be negative and 5 positive

Edited by LZY115
  • 2 weeks later...

Hi all, thought this info might be useful, reproduced from the Jaycar forums from the link above (thanks to LZY115!):

I have just completed the hand controller and IEBC unit. There is indeed a missing connection on the updated printed circuit board for the hand controller.

There should be a connection between pin 14 on the LCD display module to pin 10 on the DB25 socket. In reality these two PCB pads are very close together and can be linked by a small solder bridge. Without this connection your LCD display on the hand controller will show a line of black boxes on the top line.

Also take note on what the instructions say about connecting the hand controller to your main module before powering up the main module.

Edited by DaveB

In regards to my previous post the new boards do no have this problem.

I finally got mine working. Things that I did wrong was bad solder, solder bridges, incorrect led installation, thats it, I do agree you do need some basic understand about electronics.

Also you have to check with a multimeter for continuity (low ohms connection) between pin 4 of the LCD module in the hand controller and pin 13 of IC2 of the IEBC for low ohms. Also check for continuity between pin 6 of the LCD module and pin 10 of IC2, pin 14 of the LCD module and pin 9 of IC2, pin 13 of the LCD module and pin 8 of IC2, pin 12 of the LCD module and pin 7 of IC2 and also pin 11 of the LCD module and pin 6 of IC2. Make sure that there is not a short between adjacent connections.

Everything is working except for the solenoid, tried it with hoses connect both ways and they dont work. Seem to be getting 5psi only. Not too certain is this has anything to do with me running a haltech.

Is there a problem in using injector 2, i can not locate injector 1 on the ecm loom(s15) 101 W/G, pin out 101 on mine is W/Black.

Edited by LZY115
In regards to my previous post the new boards do no have this problem.

I finally got mine working. Things that I did wrong was bad solder, solder bridges, incorrect led installation, thats it, I do agree you do need some basic understand about electronics.

Also you have to check with a multimeter for continuity (low ohms connection) between pin 4 of the LCD module in the hand controller and pin 13 of IC2 of the IEBC for low ohms. Also check for continuity between pin 6 of the LCD module and pin 10 of IC2, pin 14 of the LCD module and pin 9 of IC2, pin 13 of the LCD module and pin 8 of IC2, pin 12 of the LCD module and pin 7 of IC2 and also pin 11 of the LCD module and pin 6 of IC2. Make sure that there is not a short between adjacent connections.

Everything is working except for the solenoid, tried it with hoses connect both ways and they dont work. Seem to be getting 5psi only. Not too certain is this has anything to do with me running a haltech.

Is there a problem in using injector 2, i can not locate injector 1 on the ecm loom(s15) 101 W/G, pin out 101 on mine is W/Black.

No any injector will do (tap in only)

Have you tested the solenoid to make sure it is normally closed?

Cut the solenoid wire from the ecu and replaced the signal to solenoid with the one from EIBC?

Routed the pipes correctly? From boost pipe to solenoid , solenoid to T ...one to actuator other side back to inlet (this one has the restrictor - make hole diameter bigger for more boost.)NB note correction...I wrongly put "make hole smaller" before I deleted that post.

I had a quick look on Google and there are a number of s15 ecu pinout charts both agree that 101 in no 1 injector - some say W/G and some W/B so you will probably be OK. Solenoid is 115 o/b

^^^ Piping is correct, I dont think the solenoid is working,while listening there isn't that buzz noise the solenoid (I think) makes, s15 are a NC type, fusion on posts 16 17 on this thread had the same issue, their NC.

So should i a)joing the solenoid wire to the ecu or b) cut the wire from the ecu and wire it directly the IEBC?

In not too certain if this makes a difference but im running a haltech e8 with plug in adaptor for the wiring loom and map sensor, im almost sure that this wont make a difference.

So far im only getting 5psi, the solenoid can only go two ways and I tried both, I still get 5psi.

First Im going to check for blown fuses, then manually operate the solenoid to check for malfunctions, last will be the wiring.

One last thing, the solenoid as two wires O and O/B, im assuming O is for earth?

^^^ Piping is correct, I dont think the solenoid is working,while listening there isn't that buzz noise the solenoid (I think) makes, s15 are a NC type, fusion on posts 16 17 on this thread had the same issue, their NC.

So should i a)joing the solenoid wire to the ecu or b) cut the wire from the ecu and wire it directly the IEBC?

In not too certain if this makes a difference but im running a haltech e8 with plug in adaptor for the wiring loom and map sensor, im almost sure that this wont make a difference.

So far im only getting 5psi, the solenoid can only go two ways and I tried both, I still get 5psi.

First Im going to check for blown fuses, then manually operate the solenoid to check for malfunctions, last will be the wiring.

One last thing, the solenoid as two wires O and O/B, im assuming O is for earth?

You need to cut the wire from the ecu and tape it up - the ecu no longer connects to the solenoid- and connect the other end that goes to the solenoid to the black wire from the IEBC. The colour code you mention for the solenoid wires sounds right but I can't confirm as i have a Stagea.

With the solenoid closed or not working at all you should be getting full boost -whatever your turbo can make (1bar+ ) as the actuator should not be working at all. Have you started off with your IEBC set to zero?

^^^^^^^^^^^Im probrably not getting full boost due to vent between the solenoid and the actuator??

Maybe the hole is too big, I might block the hole completly and see what occurs.

Yeah, IEBC had 0% duty on all 64 points.

Ill cut the wire of the ecu (O/b) and wire it directly to the IEBC and block the vent hole.

In regards to the piping.

Orginal: 1- solenoid to t piece which goes to vac source and actuator

2- solenoid to intake pipe

IEBC: 1- solenoid to t piece which goes to actuator and vent goes to intake pipe

2- solenoid to vac source

^^^^^^^^^^^Im probrably not getting full boost due to vent between the solenoid and the actuator??

Maybe the hole is too big, I might block the hole completly and see what occurs.

Yeah, IEBC had 0% duty on all 64 points.

Ill cut the wire of the ecu (O/b) and wire it directly to the IEBC and block the vent hole.

In regards to the piping.

Orginal: 1- solenoid to t piece which goes to vac source and actuator

2- solenoid to intake pipe

IEBC: 1- solenoid to t piece which goes to actuator and vent goes to intake pipe

2- solenoid to vac source

If you have the hoses the right way round (on my car the pipe from the intercooler giving boost goes to the top pipe of the solenoid and the bottom pipe is the outlet) then if the IEBC is set to zero then no pressure should be getting through the solenoid and thus nothing going to the actuator or to the vent so blocking the vent will make no difference. It sounds as though the wiring is the problem and if you do as you say above that will hopefully fix it. At zero setting you should get full boost and then you can gradually turn up the numbers to bring the boost on more gradually and to limit the max boost and then turn the numbers down again when the turbo runs out of puff. Then you can adjust the size of the vent (make it bigger) to bring the boost on earlier although if that makes the IEBC work too hard at max boost (more then 80% duty cycle) then you could reduce the size of the vent a little.

BTW I'm not sure you have the original piping correct but anyway here is a photo of how it should be now (see post #41)

http://www.skylinesaustralia.com/forums/Ja....html&st=40

^^^Makes sense I should be seeing infinite boost, almost 100% certain that its the electrical wire going to the solenoid or the solenoid itself.

IMG_3791.jpg

This is the pic of a s15 one, factory piping the top part (piping that is blocked) goes to the vac sour and actuator via t piece.

Edited by LZY115
^^^Makes sense I should be seeing infinite boost, almost 100% certain that its the electrical wire going to the solenoid or the solenoid itself.

IMG_3791.jpg

Im using this pic as a reference

This is the pic of a s15 one, factory piping the top part (piping that is blocked) goes to the vac sour and actuator via t piece.

Its working its working!!!!!!!!!!!!!!!

On the s15 the way the piping goes is the same. Its just that everything looks different.

What I did wrong was joined the actuator wire, what I should have done was cut the wire off the ecu and joing it directly to the iebc.

This thread saved me from constante swearing, thanks KiwiRS4T and guys.

Its working its working!!!!!!!!!!!!!!!

On the s15 the way the piping goes is the same. Its just that everything looks different.

What I did wrong was joined the actuator wire, what I should have done was cut the wire off the ecu and joing it directly to the iebc.

This thread saved me from constante swearing, thanks KiwiRS4T and guys.

  • 4 weeks later...

Hey all,

I have built the digital fuel adjuster kit but have lost the instructions. The kit works fine but I need to adjust the trim pots and I am just guessing with the instructions. Does anyone have an electronic copy of the instructions they can pm me... Or is there anyone in newy with the instructions that I borrow for a day to make a copy?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1680, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
×
×
  • Create New...