Jump to content
SAU Community

Recommended Posts

hi guys thanks for your help with my gearbox. I changed the oil and its 100%better not as much heat, no noise and smooth changes ( :

One thing that might help is that i sythened the oil in by running a pipe into the gearbox and poured the oil in the other side instead of using a pump to pump the oil in. I found this very easy

Once again thanks heaps guys ( :

  • Replies 84
  • Created
  • Last Reply

Top Posters In This Topic

i changed my geaarbox oil on the weekend because it was crunching going into 4th at full load. put castrol vmx80, nulon addative and found about a litre of lightwieght redline oil so put that in there too.

didn't see a change staight away, but after about 200k's of driving the problem went away. now i can change into 4th at redline.

is it safe to mix oils???

Hi all.. I reckon this cold gearbox problem must be a skyline thing 'cause mine from 1st to 2nd on a cold morning is not very nice. As someone mentioned before, double clutching helps but after about 5-10mins driving around it's all sweet.

Not long ago I put Royal Purple max gear in both the gearbox and diff. It did improve my gearbox on the cold starts as it now takes less time to become smooth.. and when it is smooth it's much better than it used to be :(

Gizmo73 also used Royal Purple and he reckons it also improved his gearbox over the Redline Shockproof.

its bad to mix synthetic and mineral oils in your gearbox.

Ive been told that once you run synthetic, if you run mineral oil after, you will ruin the gear system. If you read up and do a search on it, you will understand. The synthetic oil beds into the gears, and then running mineral oil will eat away at the gears. Have a read of it, because im not 100% what it was exactly

hi guys my car produces alot of heat from under the gear stick. Do you think this is the gearbox or the exhast or sumthing? It gets quite hot after driving a while. Could it be that my trans oil is low? Any suggestions will help thank you

Mine gets hot but haven't noticed any mechanical problems well not so far anyway

its bad to mix synthetic and mineral oils in your gearbox.

Ive been told that once you run synthetic, if you run mineral oil after, you will ruin the gear system. If you read up and do a search on it, you will understand. The synthetic oil beds into the gears, and then running mineral oil will eat away at the gears. Have a read of it, because im not 100% what it was exactly

why would you use mineral???

use the synthetic stuff

if you mix 50/50 mineral and syththetic in your gearbox might not be good idea.

However if you drain all the oil out of the gearbox and refill it with either sythetic or mineral you should have no issues with oil mixing together

BUT STICK WITH SYTHETIC BETTER PROPERTIES AND LONGER LASTING

cheers

  • 8 months later...

Hey i dont know if i done it correct or not.......umm, i used the fill plug, which was on the passenger side of my car to drain the oil.....i then dropped the jack down, open the bonnet, took off the dip stick, and used a funnel to fill the trans fluid into my car (auto's have the dip stick).....is this correct???as i didnt see a drain + fill plug, only the fill plug on the bottom( i guess the fill/drain are the same in autos....as its there to just drain then?)

  • 4 months later...

Nope, definately didn't drop the oil (not that silly) just checked if I could loosen them both first, was only able to get the drain plug.

PT, yep, it's manual, but what's involved in pulling out the shifter? Just unscrew the 4 screws, lift the plate/cover then fill? (measuring the quantities of course)

I'm against filling through the shifter due to the extra difficulty in measuring the amount going in and the risk of getting that stinking crap in the interior. Get a breaker bar on to the filler plug, mine was tight as a... well it was very tight and a breaker bar was needed to get it off. I then used a $10 pump bottle from supercheap to get the oil in. I also did a write up of this process if you need further info.

Cheers

nissan reckon vmx-80, i hated the shit it was too thin

im using the thickest shit available @ repco in my rb30 box, kinda shit to drive when cold, but i used the nulon manual box treatment aswell

i fill thru the shifter, just use a funnel and measure it before you tip it in

Edited by Rednisr31

Not sure what the 33 box is like but on the 32 box the reversing switch is the same height as the fill plug. I couldn't get my fill plug undone so I took the reversing switch out and used that hole to fill it instead :D

ActionDan, beleive me, I've tried to get the bloody thing out but it just won't budge!!! Measuring the quantity of oil would be easy as would using a funnel to pour it into the shifter so it looks like it's the best bet for me at the moment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • List all of your mods. It sounds like an aftermarket ECU hitting rev limiter. Like a valet mode, or a cold rpm limiter? 
    • @Kapr Haha yeah thats the one. I missed that you had a built up engine, I wouldn't want to run it on there either then. It was good in my situation just to replace the original turbo on a stock engine. @MBS206Yep definitely not a replacement for anything name brand
    • You are selling this? I have never bought something from marketplace...i dont know if i trust that enough. And the price is little bit "too" good...
    • https://www.facebook.com/share/19kSVAc4tc/?mibextid=wwXIfr
    • It would be well worth deciding where you want to go and what you care about. Reliability of everything in a 34 drops MASSIVELY above the 300kw mark. Keeping everything going great at beyond that value will cost ten times the $. Clutches become shit, gearboxes (and engines/bottom ends) become consumable, traction becomes crap. The good news is looking legalish/actually being legal is slighly under the 300kw mark. I would make the assumption you want to ditch the stock plenum too and want to go a front facing unit of some description due to the cross flow. Do the bends on a return flow hurt? Not really. A couple of bends do make a difference but not nearly as much in a forced induction situation. Add 1psi of boost to overcome it. Nobody has ever gone and done a track session monitoring IAT then done a different session on a different intercooler and monitored IAT to see the difference here. All of the benefits here are likely in the "My engine is a forged consumable that I drive once a year because it needs a rebuild every year which takes 9 months of the year to complete" territory. It would be well worth deciding where you want to go and what you care about with this car.
×
×
  • Create New...